Keeping you up to date with the latest CorkSport Mazdaspeed news!
Category: Part of the Week
Sometimes some products get lost in out huge catalog of Mazda performance parts. We highlight the best we offer and give more insight into the design and benefits.
As the New Year rolls around, most people are looking for a change for the better in their lives.
At CorkSport we think one of the best changes you can make is more power for your Mazdaspeed. We have all the parts you need to liven up your Mazdaspeed3 or Mazdaspeed6 in the New Year.
Safety First
One of the first things to consider when modifying your Speed is the health of its engine. Performing maintenance is very important but it only gets you so far. When adding power, one of the first modifications on your list should be the CorkSport Max Flow Fuel Pump Internals.
These pump internals allow you to maximize your stock fuel system for optimum power capabilities and safer than OE A/R ratios. This means you can add the power you want and have peace of mind that your engine will get the fuel it needs.
Put the Power Down
Like the CS fuel pump internals, the CorkSport Stage 2 RMM for Mazdaspeed 3 will not directly increase the power levels of your car; however, it helps you put all that hard-earned power down. By decreasing the amount the engine can rotate, the Rear Motor Mount allows for reduced wheel hop and torque steer while providing faster throttle response and crisper shift feel.
Even we are surprised how much this engine mount changes how a Mazdaspeed 3 feels. Don’t worry Mazdaspeed 6 guys and gals, we have an RMM for you too.
Improving Airflow
Engines in an extremely simple sense are air pumps; so the faster you can get air in and out of the system, the better. That being said, some of the simplest and easiest power gains you can get from your Mazdaspeed are from upgrading the intake and exhaust. We have seen peak gains of 25ft-lbs and 33WHP from only the CorkSport Stage 2 Intake and a CorkSport Racepipe.
Checkout the dyno sheet below.
Power and torque levels will be further increased if you install a full CorkSport Turbo Back Exhaust instead of just the race pipe section.
The catback exhaust section has proven to gain up to 14WHP while the downpipe section alone has proven to gain up to 21WHP. In the dyno graph below, the downpipe car had a CorkSport Intake installed at the same time as the downpipe (hence the 50hp gain).
If that wasn’t enough flow for you, we also offer 3” and 3.5” intakes for even more airflow into your turbo. Keep in mind though, once you get into those you will need to use a new tune to ensure your car runs optimally. But check out the extra flow you get!
Turbo Upgrade
The CorkSport Drop-In Turbo is a fantastic upgrade to the stock K04 turbo that allows your car to make more power on an equivalent boost pressure. It will work with any mods you already had on your OE Mazdaspeed turbo as the CS turbo is truly a drop in upgrade. With supplemental tuning, fueling, and supporting parts, you can push your Speed to its limits.
Stay Up-to-date with CorkSport
The Next Level
CorkSport also manufactures parts that can take your Speed beyond the parts discussed above. A short list of the parts with the best power gains can be seen below:
CorkSport Camshafts: Replacement cams with extra lift to provide increased power and torque across the entire RPM range.
Bigger CorkSport Turbo? Yes, there is one in development. See this blog post for details.
No matter what your goals are for this year, CorkSport is here to help you achieve them. Whether you just picked up a Mazdaspeed and are unsure where to start, or have been driving one for years and want the excitement you once had back, CorkSport has a part for you.
That’s right folks; CorkSport’s favorite skid trays have made their way to the GEN3 Mazda 3. Whether you have a broken OE plastic skid tray or are just looking for some extra protection for the winter months, please welcome the CorkSport 2014-2016 Mazda3 Skid Tray. Made from laser cut, 0.090” thick aluminum formed to a perfect fit, this skid tray is a direct upgrade from the OE Mazda3.
From the factory, the GEN3 Mazdas come with a flimsy plastic under tray that can crack and break with the smallest of impacts.
Stay Up-to-date with CorkSport
It exists primarily to smooth the airflow traveling under your car and act as a splash shield for the engine compartment while driving in the rain but offers no real protection for your oil pan. We felt compelled to remedy this issue, and thus, the CorkSport Mazda3 Skid Tray was born.
The 0.090” thick aluminum protects your Mazda 3 from road debris, rocks, and damage to vital engine components while adding minimal weight to your car. This aluminum is the same material as our Mazdaspeed 3 skidplate, and it has proven itself to take plenty of punishment. We even torture tested one of our prototype skid trays during the 25 Hours of Thunderhill on the CorkSport Mazda 3 Race Car and had no issues.
As always, we sought out to make the installation as painless as possible while retaining all OE features. The CorkSport skid tray only uses the OE mounting locations without having to drill or trim anything. The CorkSport Mazda3 skid tray is a two-piece design that allows for a more straightforward install. Each piece is more manageable to move around for installation than the traditional one-piece design. As a bonus, it also makes the shipping is cheaper! We retained The oil and filter access panel so you can easily perform maintenance without having to remove the Mazda3 skid tray.
By extending the front of the skid tray above the bottom of the front bumper like OE, the CorkSport Skid Tray retains the smooth transition from bumper to skid tray to ensure smooth airflow under your car. You can even run the CorkSport Skidplate with the Mazda OE front lip with no issues.
If you’re worried about your oil pan or can’t seem to keep an OE skid tray in one piece, let the CorkSport Skid Plate for 2014-2016 Mazda 3 alleviate your issues.
P.S. Our two-piece design allows us to develop fitments for other models. If you’re interested in a skid plate for your car, let us know, and we might start work on one for you!
We are in the process of designing and producing a CorkSport Transmission Motor Mount, (TMM), to reduce the excessive engine movement present from the factory. Buckle up as we go through a sneak peek at some features and go through the design process and decisions that all serve to give you a better mount in the end.
Mazda 3 without sacrificing drivability or OEM fitment. Stiffer motor mounts are a great way to improve throttle response, improve shift feel, and reduce wheel hop by reducing the total amount of engine movement but they can hugely increase NVH (noise, vibration, and harshness). As such, there is a balancing act between finding an acceptable level of NVH for the performance gains you get.
Stay Up-to-date with CorkSport
In a typical front wheel drive car the engine is mounted in a transverse matter, that is, the engine is parallel to the axle centerline. So when the engine tries to turn the wheels, the force to do so tries to make the engine rotate in the opposite direction. Motor mounts resist this motion of the engine.
Initially, we wanted to change the orientation of the factory mount for the Mazda3 to use the polyurethane bushings in the most optimal way possible as the bushings function best when they are parallel to the axis of rotation. Doing so proved to be difficult as we were effectively creating a new pivot point in the system.
Going through this design, we also realized that overall size was becoming a problem as different transmissions have varying heights. Since this mount sits right above the transmission, this was a vital thing to keep in mind. So for our 2.5L manual Mazda 3, we had a good amount of room below the mount, but it needed to go on a serious diet to fit an automatic model. This meant moving to a drastically smaller bushing which likely would have increased NVH, only using the mount for manual models, or using a custom bracket for each different transmission & model. Check out down below for one of the early (and ugly) designs.
So we went back to the drawing board. We decided to move forward with a design similar to the OE design. Doing so allowed for a smaller mount, easier manufacturing, and a significantly wider applicable model range. This includes all 2014-2016 Mazda 3, all 2014-2016 Mazda 6, and 2013-2016 CX-5 (we have not confirmed the 2017+ models years yet, but there’s a good chance this will be compatible).
Even though we went to a similar design to OE do not assume it’s the same thing. The CorkSport mount has the same diameter bushing as the OE mount; however, the OE mount does not utilize all the available space. This means that in addition to the stiffer polyurethane material, there is simply more material to resist the engine’s movement.
The CorkSport TMM utilizes billet aluminum for the main body of the mount with stainless steel plates for the washers and the angled section of the mount. This provides a more attractive and lighter mount than the OE offering while retaining the same strength and fitment of OE. Check out the picture down below for a look at one of our 3D printed prototype test fits.
We just received our first functional prototypes for further fitment and testing since 3D printed plastic parts don’t support an engine & transmission very well. With these samples, we can determine exactly how stiff to make the polyurethane and finalize the best possible design for you. During our test fit, we even noticed some deterioration of the OE mount.
This OE mount came off of the CorkSport Mazda 3 racecar. While it does not have many miles, they have all been racing miles that are very hard on all vehicle components. Check out the image down below to see a comparison between the used mount (left), a new mount (center), and the CorkSport prototype TMM (right). It’s interesting that Mazda has made some changes to their OE mount in the last few years. What you can’t see very well is that the racecar’s mount has areas where the rubber is starting to separate from the metal center section of the mount. There are even a few small tears forming on some of the inner bushing surfaces.
These signs of wear are encouraging to us at CS since this means we are helping to solve a potential problem facing 2014+ Mazda3 owners. As such we could not wait to get the TMM on a car for testing. Fitment is great so far, and we were even able to overcome some minor manufacturing errors. The first test for the mount was with the CorkSport Mazda 3 racecar at the 25 hours of Thunderhill. This event is an endurance race that runs for 25 hours straight.
The Mazda3 completed 613 laps during this time covering over 1800 hard miles. This is a torture test for any part, and I’m happy to report that the CorkSport TMM passed with flying colors. The drivers liked the mount and Derrick (who owns the car) reported greatly reduced slop in the transmission when shifting. Here is what the mount looked like after the 25-hour long race:
Aside from being very dirty and having a few scratches where it was bolted down, the mount had no issues and was still in good working condition. It already has a new home in a daily driven Mazda 3 to get even more testing done. Initial impressions are good, but we will look to decrease NVH as much as possible before any of you get your hands on it. Look for the CorkSport 2014+ Mazda 3 Transmission Motor Mount in the next few months.
Stiffer motor mounts are a great way to improve throttle response, improve shift feel, and reduce wheel hop by reducing the total amount of engine movement but they can hugely increase NVH (noise, vibration, and harshness).
Today I want to share with you a simple blog on just one way of taking your Mazdaspeed to 400WHP. After checking out this blog, If you would like more in-depth information on upgrading your Mazdaspeed with more horsepower then check out 500 WHP post for Mazdaspeed 3.
Let’s Get Started
The MZR DISI engine in the Mazdaspeed platform has been around for just over 10 years now. CorkSport along with the community of racers, shops, and enthusiasts alike have learned quite a bit about these engines. We have learned what they like and what they don’t. How they react to certain mods, how to maintain them, and also some of their weak points. We also learned how to take this platform well over 400 WHP.
We recently hit 684 whp with the CST6 Mazdaspeed Turbo — Check it out here.
Among the many things we have learned, we have developed a great understanding of what is needed to get these engines to make power. More specifically, with the right set of bolt-on parts and tuning one can easily and safely make 400WHP on a stock bottom end of your Mazdaspeed 3 or Mazdaspeed 6. The torque will just need to be kept under control.
It’s not a secret or rocket science on how to achieve this power level in a Mazdaspeed3 or Mazdaspeed6, and it is very much doable.
Stock Mazdaspeed3
Disclaimer:
There are certainly many variables that can come into play when trying to achieve 400WHP safely, such as the health of your engine, quality of engine tune, octane rating of fuel, engine management software and more. This is by no means an all-inclusive guide and the only way of making this level of power. However, this is a tried and tested method of making high power safely and reliably. We come from years of experience doing it ourselves and helping the community with their Mazdas as well. We have spent years and years developing this platform and continue to do so on a daily basis. What I aim to do is educate you on how you can make the most out of your MZR engine.
Necessary Upgrades To Make 400WHP
Now before we get too ahead of ourselves, there are two modifications that are a must before going down the 400whp quest. Those are high-pressure fuel pump internals and a tuning solution such as those provided by COBB or VersaTuner. These parts do not inherently increase hp and tq levels, but they are 100% necessary to give you most out of your hard part modifications and do so with safe and reliable power. A high-quality tune is worth every penny, and when paired with things such as an intake or exhaust, you can capitalize even more so your parts and net more horsepower.
Understanding the DISI MZR 2.3T
The DISI MZR 2.3T is not much different than any other gasoline direct injected engine that you would find on any modern automobile. Here is how it operates:
Air goes into your Mazdaspeed.
Air is combined with the correct ratio of fuel.
The air/fuel mixture gets compressed.
A spark event occurs that ignites a controlled burn.
This event forces the piston downwards.
Exhaust gases then leave the Mazda.
The cycle repeats.
So in an oversimplified matter, that is all an internal combustion engine is – a glorified air pump with more bells and whistles. One of the best ways to make a really effective air pump is to optimize the movement of air into and out of the cylinders. For that reason, it’s best to start at the front and back of our car to help give it a little breathing room.
Intake & Exhaust
Mazdaspeed3 Power Series 3.5″ Intake
It’s no secret that an intake and exhaust system are among the most popular first upgrades for any vehicle, and it’s for a good reason. Letting air in and out of the engine as easily as we can is a great first step to create more power. Doing this will free up restrictions with the manufacturer parts, especially on a factory turbocharged vehicle. OEM parts are by and large designed with emissions regulations and pricing priorities, rather than performance.
Upgrading your Mazdaspeed to a 3” or 3.5” intake and pairing it with a turbo-back exhaust will create the airflow efficiency that we need to reach 400 WHP. We’re able to do this by increasing the exhaust pipe diameter and either eliminating our catalytic converter or replacing it with a high-flow race cat. By increasing the efficiency of airflow from entry through the exit, the engine is effectively working less to produce the same amount of power.
By adding an intake and exhaust to your Mazdaspeed, you can net an easy 50+ whp when paired with the proper tune. As you continue down the modification road, you’ll find that this is the most effective dollars spent to horsepower ratio. Now that we are able to take more of the power stroke, we can focus on getting more power to the wheels, rather than letting it be consumed by byproducts such as waste heat, noise, and vibration.
Mazdaspeed3 Exhaust Setup
Intercooler & Turbo
Another great way to make more power with your Mazdaspeed, and to get closer to 400whp, is to increase the level of boost pressure running through the engine. OEM boost levels are around the 14-15 PSI. But once we have our intake and exhaust installed on our Mazdaspeed, our tuning solution can allow us to start increasing that level into the 19-21 range.
A natural byproduct of increasing the pressure within the system is a corresponding rise in air temperature. To be able to make the most of the increased boost levels, it’s important to keep the temperature at a lower level. To do this, you’ll want to upgrade to a larger top mount intercooler (TMIC), or even go a step further and upgrade to a large front mount intercooler (FMIC) core.
The intercoolers primary function is to act as a heat exchanger, and we know that heat is the #1 roadblock for any engine to make more power. The more efficiently we can remove heat from the system, the more power we can create safely and reliably. We should also note that the stock TMIC in the Mazdaspeed platform is a terrible bottleneck in the system so this will free up extra flow.
Mazdaspeed Front Mount Intercooler
Now that we have a good way of getting air into, out of, and keeping it cool at the same time, we want to increase the total volume. An easy way to do this is by upgrading the turbocharger in your Mazdaspeed. This is an easy process that replaces your factory K04 Turbo and creates the potential to throw down some serious power. When you reach this point in your build, you open up options on how to proceed:
Make the same power on less boost
Make more power on the same boost
Make way more power on WAY more boost!!!
If we are shooting for 400whp on our Mazdaspeed, then we generally like to choose door #3.
CST4
Side note: We highly suggest / possibly need a 3.5 bar MAP sensor and an electronic boost control solenoid (or EBCS). Once we start to increase our boost pressures north of 21psi, the OEM electronics begin to lose resolution and can negatively affect our tuning if not addressed.
By upgrading our MAP sensor we are allowing the powertrain control module (PCM) to recognize and look up higher boost targets than those equipped from the OEM unit. With this upgrade, the computer can now accurately record and look up these values. We also upgrade our electronic boost control solenoid (EBCS) to allow more fine-tuning of our maps and boost targets. An OEM EBCS just won’t allow us as fine of control of our boost pressure, which can result in some headaches as we approach higher horsepower levels.
Stay Up-to-date with CorkSport
The Finishing Touches To Reach 400 WHP
With the above combination of mods and proper tuning on a healthy engine, a medium frame turbo on pump gas can get you into the 330-340whp range. If we go another step further, we will open up more ‘breathing’ mods such as the intake manifold, taller lift camshafts, or a larger throttle body. This will stretch us into the 350-360 whp range.
That being said without the help of e85 or aux fueling we can’t go any closer to our 400whp mark. We simply hit the limits of the Mazdaspeed factory fuel system and need to look into upgrading that system as well.
Making the switch over to e85 allows us to get in the 380 range, but we soon run out of fuel injector headroom in the Mazdaspeed at this point and max out our injector duty cycle. We then have to look at aux fueling (Meth or Port Injection) as a solution to get us to our 400whp mark safely. What’s unfortunate is that at this point we are also looking at upgrading our hard parts such as our in-tank fuel pump to keep up with demand if you plan to run PI. There are quite a few options for AUX fueling which are beyond the scope of this blog.
Now, as mentioned this is not the only way of making these power levels, but it could be said that it is one of the easiest and most popular. It’s important to remember that along the way we supplement the engine with other supporting mods to ensure we are safe and can make full use of our power. Things like lower heat range spark plugs and a stage 2 rear engine mount can go a long way.
Thanks for following along and feel free to leave us a comment if you have any questions or want some more specific information on a product.
Many have tried, but few have succeeded to retrofit or modify an existing throttle body to work with the Mazdaspeed DISI MZR platform.
As you know, CorkSport does things a little differently, and as a result, we started from the ground up to create the best performance throttle body possible with no sacrifices to drivability or reliability. Introducing the CorkSport 72mm Throttle Body for 2007-2013 Mazdaspeed 3, 2006-2007 Mazdaspeed 6, and 2007-2012 Mazda CX-7.
Starting from the ground up means 100% brand new parts, no reworked or refurbished components anywhere.
We start with an aluminum investment cast body that is made to our specific design specifications.
A flat faced throttle plate is added to gain a little bit of extra flow by avoiding the bump of a traditional round pivot shaft.
Finally, new electronics are added that are based upon OE logic to avoid any tuning and calibration issues.
To retain easy installation, we knew we had to keep the OE bolt pattern. With this, we wanted to maximize the throttle plate diameter for maximum flow. We ended up increasing from 60mm to 72mm. This may not sound like a huge increase, but the OE Throttle Body fits inside the CorkSport Throttle Body with plenty of room! The 72mm size also fits well with both 3” and 2.5” intercooler piping to fit almost any TMIC or FMIC setup. Finally, we did away with the OE gasket (which is too small anyway) and replaced it with a durable O-ring that will hold up to oil, gasoline, methanol, and other fueling options that it may come in contact with.
The CorkSport Throttle Body underwent extensive testing to ensure that it will not fail during daily use and to ensure it performs as well as we expect. The throttle plate underwent endurance testing to validate the D-shaped pivot can stand the test of time. During flow bench testing, we found that the CS flows about 150CFM (~33%) better than the OE throttle body when 75% open (accelerator pedal fully depressed).
Check out the graph below for the full data.
In daily driving testing, we noticed better throttle response with no CEL or choppiness. In power testing with a midsized turbo (~GT30 size) we found the throttle body caused faster spool, but when we moved to a big turbo, things got interesting. With a GT35R, the CorkSport Throttle Body caused 100-200RPM faster spooling and an increase in power. Check out the dyno graph down below to see the difference between the CS Throttle body (blue) and the OE throttle body (green).
Each throttle body ships with fresh stainless steel mounting hardware, a 3” stainless t-bolt clamp, and your choice of silicone. We have options for FMIC, Mazdaspeed 3 TMIC (which also works for you CX-7 guys), and Mazdaspeed 6 TMIC.
If you’re looking to take your Mazdaspeed3, Mazdaspeed6, or CX-7 to the next level, or squeeze that last bit of power out of your big turbo build, the CorkSport Throttle Body can help you meet your goals.
