New Product – Power Series 3 Inch Intake for Mazdaspeed 3

CorkSport introduces an all new Power Series 3″ Intake System for the 2007 – 2013 Mazdaspeed 3

With much demand for wanting more air and a throaty roar from your Mazdaspeed engine,ย Corksport is proud to bring you our Power Series True 3-Inch Intake System.

Mazdaspeed MAF design for the intake system

We have so many people ask for bigger intakes and MAFs that we set out to make a better one. Traditionally most MAFs are constructed from a welded pipe with various fittings for the MAF sensor to sit on or they are machined tubes with various fittings welded or bolted on.

What are the limitations to the current way of doing things? Most companies call a 76mm (3โ€) MAF, 3โ€ because the outside diameter (OD) is 3โ€ or 76mm. That really doesnโ€™t tell you the amount of air the intake can flow. It tells you that you are using 3โ€ connectors but the inner diameter (ID) could be anything.

For reference, the stock MAF is 68mm ID. Once you are in the low 300whp range your MAF sensor will read 5volts. This means that your MAF is โ€œtopped outโ€ and does not have the ability to adjust fuel trims and timing properly. To get the headroom of tuning you must upgrade to a larger MAF diameter.

The Power Series 3″ Intake System is fabricated with a high polished 3-inch turbo inlet pipe and a true 3″ inside diameter MAF housing.ย The velocity stack design smooths air flow for maximum performance.

CorkSport Intake System
CorkSport Intake System

In order to increase the ability for a large MAF to flow as much as possible and still not top out we decided we wanted to โ€œbellโ€ the MAF entrance. This effectively increases the air velocity, flowing more air. This is almost a 10% increase in velocity over the non โ€œbellโ€ version of the same MAF. This is something that is not done on a welded MAF. You can also make the MAF any size you want so making a true 76mm MAF is possible. This added head room allows your mods to go further and gives you the ability to tune for more power.

"Other" Intake System
“Other” Intake System
Name – CorkSportUnitValue
Maximum Velocitym/s61.214
Name – OtherUnitValue
Maximum Velocitym/s56.198

To help with proper idle and cruise resolution we also added a splitter to straighten the air in front of the MAF giving a better signal to the ECU.

Mazdaspeed MAF housing for Short Ram intake


If you plan on upgrading or have already upgraded your turbo this upgrade is a must to keep your MAF sensor functioning within its calibrated range.

Mazdaspeed blue short ram intake

Mazdaspeed Advantage

  • Designed Specifically for Mazda:ย All CorkSport parts have been designed and tested specifically for Mazdas.
  • True 3″ MAF:ย Machined with a True 3″ inside diameter MAF.
  • Turbo Inlet Pipe:ย A precision high polished 3″ aluminum turbo inlet pipe..
  • Durable Dry Flow Air Filter:ย Reusable and water resistant, this unique non-woven filter media does not require oil to filter and trap dirt and actually sheds dirt under engine vibration, unlike cotton gauze which holds contaminates until you clean the filter.
  • Custom Reinforced Silicone Connectors:ย Constructed from multi-layer nylon braid to provide more strength and power and a smooth internal transition for less turbulence and optimal flow.
  • Upgraded Turbos:ย Highly recommended for Mazdaspeeds with upgraded turbos.
  • CorkSport Service and Support:ย Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support.

Order your Power Series 3″ Intake System today

Connect with us

Stay up-to-date on the latest news and product updates from CorkSport.

* indicates required

How to Keep Your Mazda Healthy

How to Keep Your Mazda Healthy…

As a car enthusiast, I always want to make sure that my car maintenance is up to date. In general Mazdaโ€™s are very reliable but, whether modified or stock, the life of your car depends on maintenance. Taking good care of your car today can help you avoid paying out more in the future on repairs. Here are the top tips Iโ€™ve collected over the years and have applied to keep my Mazda in tip-top shape. Hopefully, theyโ€™re as helpful to you as theyโ€™ve been to me.

Gasoline โ€“ Find What Works for You

To find out what octane your engine needs, first check your owner’s manual. The recommended level is often 87octane. Some models have high compression engines that are designed to utilize the octane levels of 89, 91 or higher. Ordinarily, your vehicle will not benefit from using a higher octane than is recommended in the owner’s manual. If your engine knocks or pings at the recommended octane level though, you may need higher octane gasoline.

Improve gas mileage with the Mazda 3 Short Ram Intake

Knocking may occur under certain conditions. A small percentage of vehicles may knock because of variations in engines of the same model due to manufacturing tolerances, or because of an unusual build-up of engine deposits. Other factors such as extremely hot weather, changes in altitude or hard driving conditions may also cause knocking.

Are you planning on running alternative fuel for your modified car? More often than not gas alternatives for modified vehicles require tuning. Every owner/tuner has its preference, but keep the following information in mind when choosing between E85 or race gas:

ยท ย ย ย ย ย ย ย ย E85 will generate significantly more power than your typical recommended octane gas, given the same amount of fuel. The burn rate with E85 is faster than standard 87 to 95 octane, plus you get lower temperatures and more power. The downside is that you will get worse fuel economy, and your Fuel Pump will need more regular cleaning.

ยท ย ย ย ย ย ย ย ย The best thing about any race fuel is its consistency. You can count on the performance of the fuel and then tune accordingly. It makes things like elevation changes, ambient temps, etc, easier to incorporate into different maps.

Oil โ€“ Change it Religiously

Change the oil in your Mazda every 3,000 – 5,000 miles depending on the type of (regular, synthetic) oil you use. If most of your miles come from highway driving (driving at a set speed for long intervals of time), you may be able to change the oil every 5,000 miles, but if you do most of youโ€™re driving in a city or suburban area, check your oil every 2,500 miles just to be safe. If the oil appears completely black, this is a sign that you need to have your oil changed.

If you change the oil yourself, remember to change the oil filter as well. If you take the car to a mechanic to have the oil changed, he should change the filter when he changes the oil. I always recommend the OEM oil Filter and Full Synthetic oil of your preference.

Tire Maintenance โ€“ Keep โ€˜em Rotated

Rotate your tires every 10,000 miles to prevent uneven wear (this means the back tires should be moved to the front wheels and vice versa). Also, keep a very close eye on your tire pressure. Mazdas use tires with a very soft tread, which means your car grips the road better, but its tires are more prone to leaks and breakage.

ย Look in your manual to see what the tire pressure of your front and back tires should be, and check all four tires’ pressure once a month to make sure no leaks have appeared.

Air Filter โ€“ It May be Cleaner than You Think

Mechanics will often try to convince you to change your air filter every time you change your oil. However, you shouldn’t have to change your air filter more than once every 20,000 miles unless itโ€™s excessively dirty.

To learn about high-performance air filterโ€™s go to:

ยท ย ย ย ย ย ย ย ย The Best Power Mod for a Mazda –ย  //corksport.com/blog/the-best-power-mod-for-a-mazda/

ยท ย ย ย ย ย ย ย ย High Flow Panel Filter –ย  //corksport.com/blog/product-release-corksport-high-flow-panel-filter/

Transmission Fluid โ€“ Keep an Eye Out

To protect your transmission and keep your car running for as long as possible, have the transmission fluid checked every 40,000 miles. In general, you don’t need to replace it until you hit 100,000 miles, but if you don’t check it and the fluid does burn out, it can ruin your transmission, a job that can cost more than a couple thousand to repair on a Mazda.

To learn about a related transmission topic go to Transmission Inserts at:ย  //corksport.com/blog/the-best-power-mod-for-a-mazda/

Battery โ€“ Inspect it When the Time is Right

As long as you are careful not to leave the light or any other battery-operated extras such as the stereo turned on when your engine is not running, your Mazda’s battery should last approximately three to four years. When approaching the five- to six-year mark, be sure to have it inspected. It is better to be prepared than to have your battery die unexpectedly when you need to be somewhere.

To learn about the ECU Relocation Battery Box, go to:ย  //corksport.com/blog/increase-room-in-your-engine-bay-with-a-new-battery-box/

What If?

As a longtime Mazda enthusiast, Iโ€™ve seen the company evolve in many innovative ways. Most recently, Mazda has focused its attention on improving the current Skyactive Technology lineup, including the SKY-G 2.0-liter gas and SKY-D 2.2-liter diesel engines.

This technology is great for those looking for good fuel economy and better engine output. But what about the enthusiast who, instead of seeking MPG, is drawn to a fun, high-performance vehicle they can enjoy driving 24/7?

Hereโ€™s what Iโ€™m thinking.

Sure, the 2.3 MZR engine had its ups and downs and can be improved by the enthusiasts who own them. But, I imagine something beyond what we have now. Consider this. What if the next lineup of Mazdaspeed 3โ€™s had a 2.5L MZR engine with an upgraded turbo and a High-Performance Fuel Pump (HPFP) to help with the volume and pressure to produce an ideal 320 HP beast that will scare your competition away?

But letโ€™s not stop there. Letโ€™s address the torque steer under acceleration with an all-wheel-drive (AWD) system. An AWD Mazdaspeed3 was shelved years ago; the automaker said the high price point wouldnโ€™t be saleable and the hatchback style wouldnโ€™t be attractive to consumers. But now, hatchbacks are growing in popularity and perfectly positioned to rival any competitor. This creates a great opportunity for Mazda to introduce this next generation vehicle. With that in mind, I ask that today we raise our fists in solidarity for this type of Mazdaspeed innovation.

Mazda. “It Just Feels Rightโ€

Jose Rivera – Mazda Community Blog

Check out the latest Mazdaspeed 3 performance parts

Quick 0-60? How fast can you stop?

CorkSport Big Brake Kit

Mazdas come with a good braking system but a simple brake upgrade will make a huge impact.

Got Brakes ?

A great upgrade choice is the CorkSport Big Brake Caliper Kit. They work great in both hot and cold conditions. This 4 piston kit is crafted from an extremely lightweight billet aluminum and is made to last on and off track.

After shaving over 16lbs of weight and ramping up your stopping power the feel and look of these brakes will clearly make your Mazdaspeed look sick.

Here is a great example of deep corner driving & passing. Without some powerful brakes you would be pushing the limits of factory abilities. Much thanks to Steven Kritzberg for the video.

The Big Brake Kit is a sexy add on and very useful. The installation isn’t too hard to tackle, take a look at the video below . Perfect fit for the Mazda 3 and Mazdaspeed.

CorkSport Install Video

Order your CorkSport Big Brake Kit

Who Wants The SKYACTIV-D?

 

I have been getting more and more excited about the Mazda Skyactiv Diesel engines which are due to arrive in North America this spring.ย  My thoughts have been a bit skewed with estimating power numbers with down-pipes, cranking up the boost, and doing crazy low RPM burnouts in the first 4 gears with mountains of torque.ย  My dreams were dealt a big blow yesterday as the news was released by Mazda that the diesels have been delayed.ย  Again.

ย  SKYACTIV-D Diesel - CorkSport

Seeking an answer as to why the holdup I went to look at Mazda’s official press release.ย  The Mazda official text is below

 

โ€œMazda North American Operations today announced that the launch of its SKYACTIV-D clean diesel engine inย North Americaย is being further delayed from its Spring 2014 announced debut timing.

While Mazda understands its SKYACTIV-D can meet emission regulation requirements without the use of a NOx after-treatment system, itย was decided that further development is required to deliver the right balance between fuel economy and Mazda-appropriate driving performance.โ€

 

I read this as Mazda wants to make sure the car is trouble free for North America and I am giving them props for this.ย  In the rest of the planet people are more familiar with diesels and the needed upkeep with urea injections to keep NOx lower.ย  Mazda is trying to do away with the need for this completely making the car similar to owning a standard petrol powered car which I am in agreement with.ย ย  Your average American is used to a diesel in an F350 or a Dodge not a passenger car and the last thing you want is people having problems with their cars and posting to Yelp about it for not understanding the real issue.

ย  SKYACTIV-D Diesel - CorkSport

So for now my burnout dreams will be just that, dreams until Mazda gets it all sorted out.ย  I wonder if they would let me take one of the 25 hours of thunder hill cars for a weekend to hold me overโ€ฆ

-Derrick

ย 

Is it the end of the world as we know it ?

It Has Begun

Looking at the Mazda corporate news feed this morning the news of the Mexico plant producing its first vehicle prompted the REM song, โ€œitโ€™s the end of the world as we know itโ€ to play in my head.

The plant is a Mexico plant (known as MMVO) which will be making the Mazda 2 and Mazda 3 for consumption in the US and other countries on this side of the planet. ย I have speculated in an earlier blog after Mazda announced that they would be building an engine plant there as well that we could see the CX5 and other vehicles being produced at the same location. ย With the goal of being able to produce 230,000 vehicles by 2016 there will be more than enough capacity to go into other models.

 

Granted I do have my hesitation about the vehicles being made there (in Mexico). ย Mazda is confident about the quality of the vehicles and they mentioned sending 150 of the plant engineers to Hiroshima for training in the production facilities there to make sure the product is consistent for the new plant. ย The same could be said for VW who produces vehicles in Mexico as well and there have been little rumors of those vehicles be inferior to the German made cars. ย Mazda does produce Mazda 2s and 3s in various plants around the planet like Thailand and Taiwan and the quality has been consistent from what I have heard over the years.

I am really pulling for Mazda to get this to work though, it will really help them be more profitable in the long run and help them out globally despite being one of the smaller car manufacturers that is independent.

Now the million dollar question, with the increased capacity, does this mean we have a better chance at getting a new Mazdaspeed 3 sooner than or later?

-Derrick