Living on the west coast, we are pretty fortunate to have access to quite a few cool road race tracks up and down the I5. There is a good handful right in our backyard of Washington State a few in Oregon State and even one that is a city track and is all of 4 miles away. Yes that one kind of spoils us as Derrick himself has worked, drove there during lunch in his racecar, qualified for a race, and then drove back all in a matter of 45 minutes. I don’t care who you are that’s just bad ass.
As we were building some engines the other night, we got to thinking about all the cool tracks that we got to visit last year in 2017 and how many other cool ones we want to check out in 2018.
So, we decided to throw up my list of the top 5 tracks that I think every Mazda owner should drive in their lifetime. These tracks are not presented in any particular order, and we’ve only actually been to half of them. No right or wrong answers here but what follows is our list of 5 tracks we think you guys should all hit up. So strap in and let’s go racing.
We’ll start with the obvious here, and that’s the one that has our favorite manufacture in the title. Mazda Raceway Laguna Seca. This track resides in the landscape of central California and has been around since the late 50’s. Known best for its infamous Corkscrew section this 11 turn race track is world famous, and you can’t play any racing video game or simulator without this track being one of the featured races. We haven’t done this one yet, but you better believe it’s on our bucket list. Fun fact, or perhaps sad fact, depending on how you look at it; Mazda will not be renewing its sponsorship this year with the world-famous race track. So that means starting in April that Mazda Raceway Laguna Seca will simply be known as Laguna Seca.
Next up is Road America. This one is a big one. Spanning over 4 miles long this is one of the longest road race courses across the World. The long straight that crosses the start-finish lets you put the pedal to the medal. We’ve seen many of cars run out of gearing on this long straight. That coupled with the fact that you have to go uphill first to start will really but that full load on your engine, but man is it fun.
For my next pick, we chose Hallett Motor Racing Circuit. Reason for that is we found it to be one of the most challenging circuits that we’ve ever driven on. And by challenging we mean it eats brakes. Granted we were always in a car that was not particularly suited for this track, but we did always find this to be a tough course. It was always challenging to lay down a clean lap, but we learned a lot from having driven on this one. We recommend this one to anyone that wants to get some good experience and refine their skill.
This next one has some really cool history and an even cooler track surface. Opening up just a few years after the end of World War Sebring International Raceway is actually built on a converted airport. The track used to be what was called Hendricks Field and was an airbase used to train B-17 combat crews. What’s even cooler is that part of this track still uses some of the original airport runways and makes for the craziest ride over the last corner. Combining a mix of concrete and asphalt this track is sure to punish even the best of drivers.
Last but not least we decided to go with Circuit of the Americas mostly because of two reasons. One it brought back Formula 1 to the United States, and we think that is super important for the sport and will help grow its fan base in the USA. 2nd because the track is new, modern, and cutting edge. Having only opened in 2012 this track is still but a baby. But like most children with time and patience, this track will be one of the worlds greatest we feel like.
There you have it. Our short and sweet lists of 5 tracks in the USA that we think are worth visiting. Maybe we will see you at one of them this year? Maybe we can trade a little paint too if you are up to it. Let us know what you think of this list in the comments below or share some of your favorites with us.
How about something a little different from the usual CS blog? I thought I would give you all a little insight into all the different Mazdas that are owned by employees. Some are daily drivers, some are full racecars, and some are…different (more on that later). So grab a cold refreshment, we’ve got quite a few cars to go through.
Modifications: Full Flyin’ Miata CAI, polished stainless piping, Turbosmart recirculating bypass valve, manual boost controller, O2 signal modifier, boost gauge. Recent Mustang Dyno showed a consistent 189.9WHP.
Corey’s Comments: Purchased new to me at 17,000 miles in 2012 for my 40th birthday. The Mazdaspeed Miata had been stored for 4 years-everything was original, even the tires. This Miata came from California and had never seen rain. I keep it in the garage and it’s mainly a fair weather/weekend car except during the summer. I enjoy taking a ride in the MSM with each of my kids, but love honking the horn at people and making my son wave back…like he knows them.
Owner: Luke Year/Model: 2009 Mazdaspeed 3 GT Mileage: 124,000
Modifications: Full bolted, built engine, CS prototype turbo, methanol injection. Too many CorkSport Parts.
Luke’s Comments: Car has been through stock turbo/stock block, CS turbo/stock block, CS turbo/built block, 35r/built block, and now CS prototype turbo/built block. Fun fact: my girlfriend went faster in my car than I did when I first bought it. Stock turbo went 12.8 @ 110mph in the 1320.
Owner: Daniel Year/Model: 2007 Mazdaspeed 6 Mileage: 68,000
Modifications: Custom front license plate delete, CS Interior LED Kit, daily driver dirt.
Daniel’s Comments: Just bought the Mazdaspeed6 a few weeks ago, doing a ton of maintenance before mods. This er fleet vehicle (whatever that means). Bought it from a guy who owned it the past ~9 years. Hoping to sneak some new Mazdaspeed 6 parts into the CS catalog and feed the zoom-zoom obsession!
Modifications: Virtually everything in the CS catalog for MS3. Plus a few prototype parts that never made their way to the market.
Comments: Affectionately called “Whitey”. On its 2nd built engine (we use and abuse this thing). This was one of Vincent’s first projects when he arrived at CS: rebuild Whitey’s engine. He just got done rebuilding it for the second time and is now breaking it in.
Modifications: Manley internals, L19 head studs, CS cams, bowl work & porting, all the bolt-ons, 28gph methanol injection, prototype CS turbo, 330mm BBK, other suspension bits.
Barett’s Comments: More info on the engine build here. Made ~465whp at the 2017 CS dyno day. My car hates me and is a constant work in progress. (Check out all the updates for Barett’s Mazdaspeed 3)
Modifications: Full CS bolt-ons, big turbo, meth injection, making 430whp 385ft-lbs. BC coilovers w/ custom rated Swift springs, BMSPEC front splitter, Varis rear diffuser, custom side skirt extensions, Volk TE37SL: front 18×11 rear 18×10, paint matched 240Z flares, 330mm Mazdaspeed3 Big Brake Kit.
Brett’s Comments: I’ve had the Mazdaspeed3 for about 4 years now. It has every CS bolt on in the catalog. Helps that I work here now. This MS3 makes ~430 WHP, and is a stock block for now; built block soon to come. I take more pictures of this car than I do anything else.
The GEN 3’s
Ready to mod your Mazda 3? You will be after you read this!
Owner: Jennifer Year/Model: 2014 Mazda 3 2.5L Hatch Mileage: 100,000
Jennifer’s Comments: The car has been used for the majority of the Mazda3 research and design at CS. This Mazda 3 is daily driven ~80miles each day to torture test CorkSport parts, it helps that the commute to my house is that far round trip. Basically, my daily drive is a perfect example of “running up a hill both ways” for this Mazda 3.
Collin’s Comments: Aside from the performance parts available at CS, I chose this car due to the extra ~30HP compared to most commuter cars. I still get 42MPG on my freeway commute. This is my first New Car I bought myself and I have loved learning how to modify on it.
Rich’s Comments: I drove around the same B2300 for many years while we built CorkSport from the ground up. I finally decided to treat myself and picked this Mazda6 up in 2014. Big shift, and I’ve loved having the luxuries of this Mazda 6.
Owner: Derrick Year/Model: 2014 Mazda 3 2.5L Sedan
Modifications: Caged, stripped, CS SRI, straight pipe to CS axleback, bunch of custom adjustable suspension, Big Brake Kit (sometimes), custom racetrack-modified bodywork.
Derrick’s Comments: This Mazda3 could not be sold as a road legal car, so I don’t drive it on the road. There are a TON of track hours on this Mazda 3 and all of it’s modifications. We basically TRY to break our test parts before we let them hit the market, which is good for me because I love to go fast.
Comments: Mainly stock so far, big things to come to the “CBR” (CorkSport Branded Ride). Brett, who has been dailying the CBR, somehow only is getting 23mpg. Expect more parts for facelifted GEN3’s with the CBR’s arrival.
The Others
Just because you may not have seen much about them and they don’t get their own category does not mean they’re not special. For me, some of the most interesting cars are down below.
Modifications:Sweet stickers for extra HP, tire shop wheels, custom faded paint
Comments: Vincent used to own this truck before selling it to be the “new” CS shop truck. He notes that it was involved in 3 accidents, each time the insurance company did not total the truck, leaving Vincent with more money than he spent to buy the truck. No power steering provides an arm workout for those lucky enough to drive this beast.
Derrick’s Comments: The ND is an interesting car for me as being a lifelong Mazda enthusiast I had never owned a Miata before. When the ND was announced I had already converted the Mazda 2 into a B-Spec car so I stopped street driving it and went back to my Rx7 turbo as my daily driver so I had gotten used to driving a car with “issues” again. When I got into the ND for the first time and drove it home it was very surreal expecting some weird sound or smelling hydrocarbons (the Rx7 is old and catless) and the car handled incredible right out of the box. Of course that lasted all of 3 months until we have Kenton Koch behind the wheel helping us out with the suspension development. It is one of those cars that I warn people, if you drive it you will want to buy one.
Owner: Vincent Year/Model: 2010 Mazda RX-8 R3 Mileage: 60,000 (original engine, no issues)
Vincent’s Comments: I had been wanting a 2nd gen RX-8 since high school. This thing revs out to 9400RPM and is super fun to drive. Just recently sold (hi Aaron) but too good to not include in this blog.
Owner: Derrick Year/Model: 1993 Spec Miata Mileage: “Lots and lots” (this car has run 25hours of Thunderhill a few times on top of all its other racing)
Modifications: Spec Miata Bilstein shock package, Eibach swaybars, illegal plunge cut cylinder head (lookup spec Miata plunge gate 2014), GLoc brakes, 949 6ul Spec Miata wheels, AIM dash & datalog system, ESR drive side drop floor, Really big radiator.
Derrick’s Comments: I took the advice of all the spec miata people and bought a built car so I didn’t have to spend 6 months building one myself. The local car was raced for a long time in the northwest and was a front running car before it was parked for a few years. I picked it up for ~6k with some extra spares and was immediately able to get on the track and go racing after the installation of the drop floor and new seatbelts. The big question I have people ask me is why did you get a SM? The real answer is the level of drivers in the class. At any sanctioned race event weekend there are always SM and someone to race against and I have personally known several drivers go into SM a novice and come out the other side in pro racing. To win at SM you have to have your shit together. To be the best you need to compete against and beat the best so here I am.
Owner: Barett Model: Mazda B2600i Mileage: ?
Modifications: Solid axle swap with Toyota running gear, 4.88:1 axle gears, rear locker, 3 feet of articulation, 8000lb winch, high bolstered seats, 35×14.5R15 Super Swamper Bogger Tires, “lots of f*ckery fabrication.”
Barett’s Comments: This was my first real vehicle, and it taught me lots about owning a vehicle, modifying a vehicle and I have more memories with this beast than I can come up with right now. I beat the SH*T out of this truck and it’s always put away wet.
Owner: Rich Model: 1988 Mazda Rx- CONVERTIBLE
Modifications: Turbo engine swap, Apexi Power FC, CS Border Style body kit, CS front mount intercooler, CS turbo back exhaust, many other mods.
Rich’s Comments: The Rx-7 is kept in the garage and it’s mainly a fair weather/weekend car except during the summer. I take it out for special occasions or to just show off every once in a while. It’s a nostalgia piece for me.
Not Pictured:
2016 Mazda 3 Sedan. Derrick’s 2nd racecar. Caged, stripped, 2.0L AT converted to 2.5L MT.
Mazda RX-7 FC. Owned by Derrick.
NA Mazda Miata. Parts car for Derrick’s Spec Miata
For those keeping score, that’s 22 Mazdas in the CorkSport garage. The cars have come and gone over the years but one thing will always stay true: our cars will be fun to drive because they are Mazdas. Here’s to more Mazdas finding their way into the CS (and your) garage.
Oh and if you have any questions on the above cars, please let us know down below, we’ll be sure to pass on your question to the car’s owner.
That’s right folks; CorkSport’s favorite skid trays have made their way to the GEN3 Mazda 3. Whether you have a broken OE plastic skid tray or are just looking for some extra protection for the winter months, please welcome the CorkSport 2014-2016 Mazda3 Skid Tray. Made from laser cut, 0.090” thick aluminum formed to a perfect fit, this skid tray is a direct upgrade from the OE Mazda3.
From the factory, the GEN3 Mazdas come with a flimsy plastic under tray that can crack and break with the smallest of impacts.
Stay Up-to-date with CorkSport
It exists primarily to smooth the airflow traveling under your car and act as a splash shield for the engine compartment while driving in the rain but offers no real protection for your oil pan. We felt compelled to remedy this issue, and thus, the CorkSport Mazda3 Skid Tray was born.
The 0.090” thick aluminum protects your Mazda 3 from road debris, rocks, and damage to vital engine components while adding minimal weight to your car. This aluminum is the same material as our Mazdaspeed 3 skidplate, and it has proven itself to take plenty of punishment. We even torture tested one of our prototype skid trays during the 25 Hours of Thunderhill on the CorkSport Mazda 3 Race Car and had no issues.
As always, we sought out to make the installation as painless as possible while retaining all OE features. The CorkSport skid tray only uses the OE mounting locations without having to drill or trim anything. The CorkSport Mazda3 skid tray is a two-piece design that allows for a more straightforward install. Each piece is more manageable to move around for installation than the traditional one-piece design. As a bonus, it also makes the shipping is cheaper! We retained The oil and filter access panel so you can easily perform maintenance without having to remove the Mazda3 skid tray.
By extending the front of the skid tray above the bottom of the front bumper like OE, the CorkSport Skid Tray retains the smooth transition from bumper to skid tray to ensure smooth airflow under your car. You can even run the CorkSport Skidplate with the Mazda OE front lip with no issues.
If you’re worried about your oil pan or can’t seem to keep an OE skid tray in one piece, let the CorkSport Skid Plate for 2014-2016 Mazda 3 alleviate your issues.
P.S. Our two-piece design allows us to develop fitments for other models. If you’re interested in a skid plate for your car, let us know, and we might start work on one for you!
We are in the process of designing and producing a CorkSport Transmission Motor Mount, (TMM), to reduce the excessive engine movement present from the factory. Buckle up as we go through a sneak peek at some features and go through the design process and decisions that all serve to give you a better mount in the end.
Mazda 3 without sacrificing drivability or OEM fitment. Stiffer motor mounts are a great way to improve throttle response, improve shift feel, and reduce wheel hop by reducing the total amount of engine movement but they can hugely increase NVH (noise, vibration, and harshness). As such, there is a balancing act between finding an acceptable level of NVH for the performance gains you get.
Stay Up-to-date with CorkSport
In a typical front wheel drive car the engine is mounted in a transverse matter, that is, the engine is parallel to the axle centerline. So when the engine tries to turn the wheels, the force to do so tries to make the engine rotate in the opposite direction. Motor mounts resist this motion of the engine.
Initially, we wanted to change the orientation of the factory mount for the Mazda3 to use the polyurethane bushings in the most optimal way possible as the bushings function best when they are parallel to the axis of rotation. Doing so proved to be difficult as we were effectively creating a new pivot point in the system.
Going through this design, we also realized that overall size was becoming a problem as different transmissions have varying heights. Since this mount sits right above the transmission, this was a vital thing to keep in mind. So for our 2.5L manual Mazda 3, we had a good amount of room below the mount, but it needed to go on a serious diet to fit an automatic model. This meant moving to a drastically smaller bushing which likely would have increased NVH, only using the mount for manual models, or using a custom bracket for each different transmission & model. Check out down below for one of the early (and ugly) designs.
So we went back to the drawing board. We decided to move forward with a design similar to the OE design. Doing so allowed for a smaller mount, easier manufacturing, and a significantly wider applicable model range. This includes all 2014-2016 Mazda 3, all 2014-2016 Mazda 6, and 2013-2016 CX-5 (we have not confirmed the 2017+ models years yet, but there’s a good chance this will be compatible).
Even though we went to a similar design to OE do not assume it’s the same thing. The CorkSport mount has the same diameter bushing as the OE mount; however, the OE mount does not utilize all the available space. This means that in addition to the stiffer polyurethane material, there is simply more material to resist the engine’s movement.
The CorkSport TMM utilizes billet aluminum for the main body of the mount with stainless steel plates for the washers and the angled section of the mount. This provides a more attractive and lighter mount than the OE offering while retaining the same strength and fitment of OE. Check out the picture down below for a look at one of our 3D printed prototype test fits.
We just received our first functional prototypes for further fitment and testing since 3D printed plastic parts don’t support an engine & transmission very well. With these samples, we can determine exactly how stiff to make the polyurethane and finalize the best possible design for you. During our test fit, we even noticed some deterioration of the OE mount.
This OE mount came off of the CorkSport Mazda 3 racecar. While it does not have many miles, they have all been racing miles that are very hard on all vehicle components. Check out the image down below to see a comparison between the used mount (left), a new mount (center), and the CorkSport prototype TMM (right). It’s interesting that Mazda has made some changes to their OE mount in the last few years. What you can’t see very well is that the racecar’s mount has areas where the rubber is starting to separate from the metal center section of the mount. There are even a few small tears forming on some of the inner bushing surfaces.
These signs of wear are encouraging to us at CS since this means we are helping to solve a potential problem facing 2014+ Mazda3 owners. As such we could not wait to get the TMM on a car for testing. Fitment is great so far, and we were even able to overcome some minor manufacturing errors. The first test for the mount was with the CorkSport Mazda 3 racecar at the 25 hours of Thunderhill. This event is an endurance race that runs for 25 hours straight.
The Mazda3 completed 613 laps during this time covering over 1800 hard miles. This is a torture test for any part, and I’m happy to report that the CorkSport TMM passed with flying colors. The drivers liked the mount and Derrick (who owns the car) reported greatly reduced slop in the transmission when shifting. Here is what the mount looked like after the 25-hour long race:
Aside from being very dirty and having a few scratches where it was bolted down, the mount had no issues and was still in good working condition. It already has a new home in a daily driven Mazda 3 to get even more testing done. Initial impressions are good, but we will look to decrease NVH as much as possible before any of you get your hands on it. Look for the CorkSport 2014+ Mazda 3 Transmission Motor Mount in the next few months.
Stiffer motor mounts are a great way to improve throttle response, improve shift feel, and reduce wheel hop by reducing the total amount of engine movement but they can hugely increase NVH (noise, vibration, and harshness).
For many people across the USA, the days after Thanksgiving means one thing. To them, it’s the start of the Christmas season. The beginning of holiday shopping, pumpkin spice lattes, and the best home-cooked meals you can’t wait to dive into.
However, for a small select few group of individuals and teams, it’s a time for something completely different. It’s a time to see what you are made of, a time to put it all out on the table. A time where you know if the past year of planning, testing, and preparation are about to reward you greatly or tear you down completely. It’s the time when you hope to be able to stand up on a Sunday at noon and say proudly, “I survived the 25.”
For those lucky few (some call them crazy or stupid) the weekend after the Thanksgiving Holiday is what you might call a different type of holiday.
For the past 15 years, the 1st weekend of December is when some of the world’s best pro and amateur drivers descend upon a small city in Northern California known as Willows. Just on the outskirts of this quaint little city lies a little well-known road course titled merely “Thunderhill.” Now what makes Thunderhill so unique, well it’s probably the fact that this venue host the longest and most extreme endurance race in all of North America. For 25 hours straight; teams, coaches, drivers, and fans endure the rain, cold, dark, lack of sleep and more to try and make a name for themselves, and this year CorkSport did just that. Made History…
While attending the 25 Hours of Thunderhill is nothing new for CorkSport as we have spent the past several years supporting Mazda North America and their racing efforts with logistics, crew, and parts. This year was the first year where we entered a new team ourselves and brought our car, crew, trailer, and everything else you need to try and survive 25 hours of racing.
Sadly MNAO did not attend this year so it was up to us to make sure that the brand and name would make a forceful showing at the event and that is precisely what we did.
To start this whole thing off, we brought out our 2016 Mazda 3 GT. You guys are more than familiar with this car as Co-owner, and founder of CS Derrick Ambrose has been piloting this ride for two race seasons now in SCCA racing. We spent several weeks leading up to the event preparing the CorkSport Mazda3 for this daunting task.
.
We got extra safety equipment installed, upgraded our data acquisition package, optimized and engine tune for the 2.5L engine, and even installed some upgrade prototype pieces to have the car suited for the race.
Some of the CS goodies that were on the car during the run where our SRI, Cat-back exhaust, RMM, sway bar, and some prototype pieces like our aluminum skid tray and upgraded transmission engine mount. We needed the best parts we could get in there if we wanted to be competitive and make history.
No one has ever raced the 3rd generation Mazda 3 for this long in any endurance race. This car started off just like any other Mazda 3 and still retained a full OEM chassis, transmission, and engine. The engine internals where untouched and the transmission received a CorkSport LSD.
The team showed up on a brisk and cold Thursday morning, and we went to work. We immediately set up and got the drivers briefed.We got some practice in on Thursday, followed by some qualifying on Friday, all to be prepared to push this car to the limit for 25 hours. The team grabbed the pole position, and we were 1.5 seconds ahead of the next car which was fantastic. It showed we had the pace and, ultimately, the faster car. Fast forward to Saturday, and the flag drops green.
We had a great start and excellent drivers in the car. We struggled a bit through the night with consuming tires at a rate faster than we had anticipated and also had a few issues with how quickly we could get fuel into the car, despite the problems the team and the car pushed through the night. With just a brake change and tweak to the exhaust through the night, we maintained a good pace that ultimately got unwound due to the fuel issue mentioned above.
There was a Miata in our class that could get better fuel economy and tire consumption and slowly crawled there way up to lead during the night.
As the sunlight begins to break through, we are in a healthy 2nd place but a bit far off the leader, however, it does not worry us too much as we still have a shot at a win. Things were looking good till right about hour 22. One of our driver’s radio’s in and let us know he lost 4th gear (that’s not good). None the less we keep pushing knowing we have a spare transmission should we need to swap.
Now at hour 23 we get another message. “I lost 2nd gear” The transmission has now lost two gears, and we get a bit nervous. The car is still going and driving strong but our lap times do suffer from not being able to use all of the gears. After a quick powwow with the team, the decision is made to leave the car out on track and finish the race between 3rd and 5th gear.
With only 2.5 hours to go swapping out the transmission did not make sense as we were very secured in 2nd place. So we did just that and pushed on through, and you know what happened? We did it. While we didn’t get the P1 spot like we had wanted we did what no other SKYACTIV-G Mazda3 had done before.
We survived the 25. We proved the chassis and the platform, we pushed harder, longer, and further than absolutely anyone else has. The car was relatively unscathed, and minus the transmission, the vehicle performed excellently. All of the CorkSport parts did precisely what they needed to and outperformed all expectations.
We took the 3rd gen platform and solidified it as a competitive car and chassis that can be used and used well at all levels of motorsports.
So, what happens next?
The Mazda 3 made it back home and now lay dormant inside of HQ. We will be spending the next few weeks going through a ton of data and running through the car with a fine tooth comb.
We’ll take the transmission apart and see what her demise was. We’ll likely strip the SKYACTIV 2.5L down as well to check out what two years of racing looks like on her. The oil is already out of the car and on its way to the lab so be sure to stick around and see what we find out there.
Now one of the great things about this is what our success brings to the community. Everything we learned here can and will be applied to all of our parts and products moving forward. When we win, you guys all win. So, celebrate our accolades with us and wish us luck as we begin to prepare for the 2018 race season.
Do we tackle the 25 hours again next year? Do we show up with a turbocharger and more aero? And do we fight our ways to a P1 finish? You better believe I am going to try.
