4th GEN Mazda 3 SRI

4th Gen Mazda 3 Power

We are proud to announce our first product specifically for the 4th GEN (2019+) Mazda 3: the CorkSport Short Ram Intake. Gain horsepower, torque, and some much needed sound from your 2.5L SkyActiv-G in only about 30 short minutes. Features include an AEM dry-flow filter, a billet machined MAF housing, a custom designed reinforced silicone coupler, and stainless steel T-bolt clamps that combine to be a great and simple upgrade for your new MZ3. Read on for more details!

Increase horsepower in your 2019+ Mazda 3 with the easy to install Intake
CS Short Ram Intake

We’ll admit this intake has been a bit of a challenge since Mazda has switched to a new style of MAF sensor that is very sensitive to changing the intake. We’re happy to report that we’ve figured everything out and have had 5 cars successfully testing the intake for hundreds of miles with no issues. Now, onto the fun stuff!

Let’s jump right into the fun stuff: power! By removing the restrictive factory intake and filter, and replacing them with the CorkSport SRI, we were able to pick up 5-7WHP and 5-7WTQ when tested back to back on our dyno. This was tested within an hour or so of each other, with no tuning changes, and with the only change being the intake swap. Check out the dynograph down below! For both intakes, the only other mod on the test car was a prototype CS axle back exhaust (coming soon!). This will not affect power gain from the intake as it was installed for both tests.

Dyno proven power gains for your 4th Gen Mazda 3
CorkSport

Power is not the only benefit though. The CS short ram intake offers a great visual boost to your engine bay. You can even personalize your intake as you can select between red, blue, and black silicone and filter as well as polished or black clamps. Appearance is not even the best part-the CorkSport intake adds some much needed growl to the engine to give some more excitement when you get on the gas. It’s not obnoxious, but noticeable and definitely enjoyable.

The CorkSport Gen 4 Mazda 3 SRI installs in 30 minutes
Check our 4th Gen parts selection

To make the power and great noise, each component in the CS SRI has been optimized for performance. Starting at the filter, an AEM Dry-Flow is used for fantastic air flow capacity without compromising filtration. A non-oiled filter is used specifically to prevent issues with the MAF sensor.

Next comes the billet MAF housing. We use a precision machined MAF sensor housing to ensure the diameter of the intake near the MAF sensor is an exact match to the OEM diameter. This keeps fuel trims in check and keeps the check engine light off. A billet MAF housing has the added benefit of looking great, especially when finished off with an attractive laser etched logo.

We have 3 color options available for the 2019+ Mazda 3 intake
CorkSport Short Ram Intake

The MAF housing connects to the throttle body with a custom designed and reinforced silicone coupler. It is a perfect fit with the OEM throttle body and valve cover vent hose while the four layers of nylon braiding keep the silicone strong for years to come. This piece of silicone has the added benefit of being completely smooth on the inside versus the accordion OEM rubber piece. This helps promote flow into your engine.

Finally, all of the components are tied together with stainless steel T-bolt clamps. These clamps offer superior sealing characteristics over a traditional worm gear clamp and are not prone to stripping like a worm gear clamp.

Mazda3 Gen 4 Performance Air Intake System
CorkSport SRI

The CorkSport GEN4 Mazda 3 Short Ram Intake is finally here and it’s a great upgrade to start getting your 2019+ 3 to perform as good as it looks. Be sure to check out the product listing and video and don’t hesitate to give us a call with any questions!

4th Gen Mazda 3 Sport Springs

The 2019+ 4th generation Mazda 3 is a car that certainly divided opinions when it came out. From its divisive looks to the new torsion beam suspension, even we weren’t quite sure what to make of it at first. However, we have since fallen in love with our shop 4th GEN, a big part of it is what we are releasing today: the CorkSport Performance Lowering Springs for 2019+ Mazda 3 (Sedan & Hatchback for both AWD & FWD). Give your new 3 an aggressive look that is sure to turn heads while improving the handling for those twisty backroads!

2019-2020 Mazda 3 lowering springs
Gen 4 Lowering Springs

Let’s start off with the elephant in the room: ride height. When we developed these springs, it was somewhat difficult as we had to account for different body styles, transmission options, and now even driveline options. With all things taken into account, we found the right range of ride height that looks great on the lightest, heaviest, and all options in between.

The perfect balance of lowering for the 2020 Mazda 3
Why Lowering Springs?

On the lightest GEN4: hatchback, front-wheel drive, manual trans, the CS lowering springs offer 1.5” front and 1.8” rear ride height drop. On the heaviest GEN4: sedan, all-wheel drive, auto trans, the CS lowering springs offer 1.6” front and 2.2” rear ride height drop. Depending on your vehicle’s options, you will end up at or between these extremes. Don’t worry though, your ride ends up sitting level no matter what combination of options you have. The images below show the lightest (upper) and heaviest (lower) Mazda 3.

AWD Mazda 3 low down springs
CorkSport

We also focused heavily on improving the handling with the CS GEN4 lowering springs. A lower ride height means a lower center of gravity which when combined with a stiffer spring rate, means less body roll. This improves handling feel and driver confidence when attacking a backroad. We even increased the rear spring rate more than the front to reduce understeer and help with turn-in.

All Lowering Springs

The CorkSport 2019+ MZ3 springs went through a few different iterations of spring rate and ride height before we found the best balance of ride quality, handling, and appearance. The final spring rates are 3.4K front and 5.9K rear. Compared to the OEM rates of 2.23K front, 4.20K rear, we made a decent jump in rate; however, the new springs are well within the OEM damping rates. The ride is obviously stiffer than OEM yet is not bouncy and you can still comfortably daily drive on the springs.

The perfect lowered stance for your 4th Gen Mazda3
CorkSport

During development, we even tested for the natural frequency changes in the suspension from installing lowering springs. Essentially, the natural frequency is a good way to compare how “stiff” one car feels compared to another, even if their suspensions are different (for more background info on natural frequency, check out this blog). We went from an OEM of ~1.6Hz front and rear to 1.75Hz front and 1.8Hz rear on the CS lowering springs. This increase is enough to feel “sporty” but not enough that it will ruin your drive to work.

FWD or AWD the springs work on all 2020 MZ3
Gen 4 Springs

As with all CS lowering springs, they are a direct fit install that can completely change your car in only a few hours. The only permanent modifications are trimming the OEM bump stops to account for the lower ride height. To ensure they will last as long as your car, each spring is made out of high tensile strength spring steel, which is then powder coated blue for corrosion resistance and a great look. The rear springs even include spring silencers to prevent any added noise from the lowering springs.

The CorkSport GEN4 Mazda 3 Lowering Springs have really changed our opinion on the new body style. With the right set of wheels, our CS shop car turns heads all day long and would fit right in at any car show. If you’re ready to upgrade your 3’s handling and give it an aggressive look, we are happy to help! Give us a call if you have any questions, and be sure to check out the product video on the web listing!

2019 Mazda 3 – What’s new with the suspension?

With the introduction of the 4th generation Mazda 3 there are many questions around the new chassis, engine, interior, and many other components. Here we are going to start investigating the suspension as we move through the process of developing sport lowering springs for the 4th Gen Mazda 3.

View all Mazda 3 Parts

If you didn’t know already, we recently purchased a 2019 Mazda 3 Premium with the 6 manual transmission and Snowflake white paint. Right out of the box the 2019 has impressed us with its intuitive driver feedback through the steering wheel, pedals, and gear shifter. The interior is phenomenal and the exterior is…growing on us.

BUT enough of the chatter lets throw the car on the lift and take a look at the suspension.

CorkSport

At the front of the car, we have a pretty typical McPherson strut assembly with a lower control arm. This type of suspension is very common in modern passenger cars because it is simple, durable, and cost-effective. There are tons of aftermarket support for this type of suspension because it is so common, but from a purely performance standpoint, it does leave something to be desired.

Comparing the 2019 to our inhouse 2018 3rd Gen you can see one major difference. The connection from the steering knuckle to the strut body is now a simple clamp collar vs the two-bolt connection on the 3rd gens. We imagine this was purely a cost-cutting design change. For you, the result is just a slightly more difficult installation.

View all of our Lowering Springs

At the rear of the car, things are drastically different. Instead of the more standard multi-link trailing arm suspension, we have a torsion beam style suspension. Mazda says this was “to reduce unwanted movement in the suspension and increase driver comfort”, but sadly we believe this is straight-up cost cutting at the sacrifice of performance.

Check our 3rd Gen Suspension options

We could go into a bunch of nerdy details here, but in a nutshell, going from multi-link trailing arm to torsion beam takes away our ability to adjust and control camber, toe, and rear roll stiffness because all of these major suspension dynamics are integrated (or discarded) with the torsion beam design. Never fear, the Team at CorkSport Mazda Performance is working on solutions to this, but it will be a challenge.

Now specifically looking at the rear springs, you can see that the spring is very short. This caused some difficulty in design, but we have successfully overcome this hurdle.

View all of our current lowering springs

We’ve tested the OEM springs rates and WOW are they soft. We developed prototypes to validate our target springs rates and have been driving on those for about a few months now. Happily, from this testing, we’ve found that the OE struts/dampers damping rate is more than sufficient for proper sport lowering springs. With that complete, we’ve designed multiple sets of lowering springs with various ride height targets and our tested springs rates.

Lastly, we tested various final prototypes to get our final ride height just right. Ladies and Gentlemen, these will be LOW and will work with Sedan, Hatch, AWD, and FWD!

We are excited to release final production units to the public in #twoweeks. It is important to note, CorkSport 7th Gear Members will have an opportunity to purchase these springs a week before the general release and they will receive free shipping (in the lower 48 states), as part of their membership benefits!

If you have not seen what the future holds for your 4th Gen Mazda 3, see our product pipeline blog here. If you have ideas or feedback, please let us know. We are listening, we want to hear from you!

-Barett @ CS

Performance Parts for the 4th Gen Mazda 3

Today we are going to lay it all out; we are going to tell you about what we are working on for your Mazda 3 and WE ARE EXCITED!  Who are we?  If you don’t know already, we are CorkSport Mazda Performance based out of Vancouver, Washington.  We are the number One Performance Aftermarket Mazda Parts Company and we have set our sights on the 4th Generation Mazda 3.

Below are the first projects we are developing for the 4th Gen Mazda 3 and CX30.  Engine performance, suspension performance, and styling are all covered here and we are closer to launch than you may realize.  Sit back and enjoy, there’s a lot here and we want you to see it all. 

CorkSport – Lowered on CS Springs

One of the most sought after and anticipated performance items for the 2019+ Mazda 3 are the CorkSport Sport Lowering Springs.   The CS springs provide the most aggressive drop on the market today while providing a sporty and comfortable ride for daily driver use.  With that, we have confirmed fitment on FWD manual transmission hatch and AWD automatic transmission sedan.  We found that the Auto AWD Sedan rides just slightly lower, but is still within proper ride height for suspension function.

See all of our Lowering Springs

We design our springs with more than just looks in mind (but they do look great).  Spring rates and the suspension frequency are critical to performance and comfort.  With that being said we increased the front spring rate 52% and rear rate 40% based on the OEM 2019 FWD Hatch MT springs.  

CorkSport

Now if you’re looking at the images and thinking “Damn those wheels look good” then you are correct and we agree; they look amazing and fit the car and CorkSport springs perfect.  

Here are the specs: Advan RS 19×8.5 +38 with 235/35 Kumhos.  We have just the slightest rub on the inner fender on large bumps.  Besides that they are perfect and you can have this setup too!

See all of our Axle-Backs

Next up is the CorkSport Axle-Back Exhaust.  Off the showroom floor, the Mazda 3 is ghostly quiet which is pretty disappointing. Our goal with the Performance Axle-Back Exhaust is a noticeable but mellow tone that you can enjoy every single day; gents this is Wife/Girlfriend approved. 

CorkSport – Using OEM Springs

We are proud to announce that will we be supporting multiple models on launch.  We have confirmed the Sedan, Hatch, Hatch w/Aero Package, and the CX-30.   Along with that we have confirmed fitment for both FWD and AWD models for all cars listed.  

See all of our Strut Bars

Look closely, there’s a couple new products in this engine bay…long in development is the Short Ram Intake System which replaces the OEM airbox with a high flow dry element filter, billet aluminum MAF housing, 4-ply silicone coupler, and stainless steel T-bolt clamps.  

Upon launch we will be offering various color combinations between Black, Red, and Blue.  You can see them below.   

See all of our Intakes

In our testing we have seen repeatable 5whp gains at peak with a nice increase across the RPM range.  Street driving our butt dyno agrees with crisp throttle response and a lovely intake induction noise.  The combination of induction noises, exhaust note, and sporty feedback from the sport springs really turns the Mazda 3 from an A-to-B car to a great enthusiast hot hatch.  

CorkSport

The other project sitting in the engine bay is the CorkSport Front Strut Brace.  Bracing the strut towers to each other improves chassis stiffness and reduces suspension complicity.  This results in increased driver feedback and thus a better driving experience.  The powder coated steel brackets and polished aluminum cross bar add a nice loot to the engine bay.  

See all of our Swaybars

Lastly, and still in development, are the rear sway bars for the FWD and AWD 4th Gen Mazda 3.  This project has been interesting because of the new torsion beam rear suspension found on the 4th Gen Mazda 3.  It’s interesting because there is no factory equipped sway bar.  Instead of just developing a larger rear sway bar, we are developing a sway bar from scratch along with the attachment methods.  

You also notice that there are two different bars in the image.  This is because the AWD and FWD torsion beams are different due to the AWD drivetrain.  Long story short, we are developing a RSB for each drivetrain specifically because that’s the correct way to do it.  

Wow, that was a lot, and trust me there is more we are investigating, but we can’t let ALL the secrets out yet.  We would love to know what products you would like CorkSport to develop for the 2019+ Mazda 3 platform, you can do so right here by Submitting a Product Idea.  

Also, we love sharing with the community directly and have been doing so in these groups.  If you don’t know about them then check them out and join for more info.  

Thanks for tuning in with CorkSport.  We hope you are as excited about the 4th Gen Mazda platform as we are!

-Barett @ CS

The First and Only Performance Mazdaspeed Throttle Body with NO Sacrifices

Mazdaspeed3 intake manifold and throttle body installed

The First and Only Performance Mazdaspeed Throttle Body with NO Sacrifices

Many have tried, but few have succeeded to retrofit or modify an existing throttle body to work with the Mazdaspeed DISI MZR platform.

As you know, CorkSport does things a little differently, and as a result, we started from the ground up to create the best performance throttle body possible with no sacrifices to drivability or reliability. Introducing the CorkSport 72mm Throttle Body for 2007-2013 Mazdaspeed 3, 2006-2007 Mazdaspeed 6, and 2007-2012 Mazda CX-7.

Starting from the ground up means 100% brand new parts, no reworked or refurbished components anywhere.  

We start with an aluminum investment cast body that is made to our specific design specifications.

A flat faced throttle plate is added to gain a little bit of extra flow by avoiding the bump of a traditional round pivot shaft.

Finally, new electronics are added that are based upon OE logic to avoid any tuning and calibration issues.

To retain easy installation, we knew we had to keep the OE bolt pattern. With this, we wanted to maximize the throttle plate diameter for maximum flow. We ended up increasing from 60mm to 72mm. This may not sound like a huge increase, but the OE Throttle Body fits inside the CorkSport Throttle Body with plenty of room! The 72mm size also fits well with both 3” and 2.5” intercooler piping to fit almost any TMIC or FMIC setup. Finally, we did away with the OE gasket (which is too small anyway) and replaced it with a durable O-ring that will hold up to oil, gasoline, methanol, and other fueling options that it may come in contact with.


The CorkSport Throttle Body underwent extensive testing to ensure that it will not fail during daily use and to ensure it performs as well as we expect. The throttle plate underwent endurance testing to validate the D-shaped pivot can stand the test of time. During flow bench testing, we found that the CS TB flows about 150CFM (~33%) better than the OE throttle body when 75% open (accelerator pedal fully depressed).

Check out the graph below for the full data.

In daily driving testing, we noticed better throttle response with no CEL or choppiness. In power testing with a midsized turbo (~GT30 size) we found the throttle body caused faster spool, but when we moved to a big turbo, things got interesting. With a GT35R, the CorkSport Throttle Body caused 100-200RPM faster spooling and an increase in power. Check out the dyno graph down below to see the difference between the CS Throttle body (blue) and the OE throttle body (green).

Each throttle body ships with fresh stainless steel mounting hardware, a 3” stainless t-bolt clamp, and your choice of silicone. We have options for FMIC, MS3 TMIC (which also works for you CX-7 guys), and MS6 TMIC.


If you’re looking to take your Mazdaspeed3, Mazdaspeed6, or CX-7 to the next level, or squeeze that last bit of power out of your big turbo build, the CorkSport Throttle Body can help you meet your goals.