Red Baron Speed of Newberg

My Name is Symon Powlison and this is my journey of how I got my Mazdaspeed3 and the Mazda community that became my family. 

Let’s head back in time a bit, I was a broke high school student and I had just bought a 1997 dodge avenger, while my friends had all dabbled with modifying their cars at the time, I had not, but I knew I wanted to. The avenger came with an exhaust that sounded ok and some wheels and that’s about it.

When I showed my new car to my best friend Barett (yes Corksport Barett) and talked about build aspirations that never happened, we decided that we both wanted new stereo and subs, 2007-2008 was the time for loud music and lots of bass lol, “Darude Sandstorm” anyone? 

I had a lot of fun with that car but long story short the car was towed away late in the night for having a flat tire in a parking lot. Now with little to no money and my little avenger was never to be seen again. All is not lost though because those early years with that car started me on a slow trek of building my own “Racecar” later in life it was the catalyst that started it all. 

Fast forward to the year 2012, I’m a bit more established now and I’m getting ready to deploy at the first of the year for 10 months, when my Co-Worker decides to buy a BMW 335i, I made the brash decision to follow suit and I purchased a 2004 Audi S4, my wife was needing a new car anyway so I gave her the Kia Optima I had purchased a few months back. 

Everybody was happy because I got my car and my wife got a brand new Kia! My Audi came with Tien lower springs, a nice fender roll job, and a Magna-flow exhaust. The roar of the V8 through the exhaust was great, it had quick get up and go and it looked amazing in the brilliant red paint. This was my first experience with a “quick” car and I was hooked, but with Audi’s, I had no idea how to even begin to work on it if it had problems, and neither did anybody close to me. This is when I knew this wouldn’t last but I thoroughly enjoyed it when I had it. 

Symon Powlison

During deployment, I would leave my Audi in the hands of Barett, and return to resume driving bliss with the car, until I left again except this time it would be for nearly 3 years. My wife and I left for Korea in the middle of 2014. My car was out of my possession longer than in my possession and thus while my time away I grew apart from my Audi and wanted something new, different, I wanted a hatchback. 

I always liked the way hatches look, the bodylines, the mildly flared fenders, the base stance of the hatchback drew me in. I spent countless hours looking at every model of hot hatches, tirelessly and sometimes redundantly, maybe I could afford this or maybe I should buy. I decided to call Barett from Korea and told him I was coming home and I wanted to sell the Audi and get something I truly desired. 

He mentioned getting a Mazdaspeed3, I had seen some videos about them but I was rather set on an all-wheel-drive hatch to drive in the snow, but that was dumb because I hate driving in the snow lol. I decided to give the Speed a deep dive look and man I was impressed, not to mention I had an endless resource if I needed any help. 

I was sold, the price was right, the whole car package was right, it checked all my boxes, I wanted a turbo 4cyl with good base stats, something reliable to a degree, and something that I could learn to modify and have help if anything breaks. 

I arrived home in the spring of 2017, and scoured the interwebz and found the speed of my dreams, a velocity red 2013 tech package mazdaspeed3 with 69k on the dash. With what money I had left in savings, a small income, and an Audi for a deposit. I marched down to the dealership and literally, 6 hours later I walked out of there with my dream car. 

Shop all 2010-2013 Mazdaspeed3 Parts

Funny side note here, when I took the MS3 for a test drive I was by myself, I never drove a 6-speed manual car before and didn’t know how to put the car in reverse, so here I am sitting in somebody’s driveway (huge facepalm) trying to figure out how to put the car in reverse when the homeowner comes out and asks if I need help. I tell him the story he laughs and gives me a push to send me on my way back to the dealer. 

That test drive officially sold me on the car, I can still remember the first time starting that car and the first time I hit 15psi of boost, it was amazing and probably the coolest feeling ever while driving. I couldn’t wait to show my wife, I ripped the speed all the way home, and it was nothing but smiles per gallon. I couldn’t have been happier. I am honored to have such a loving wife who was just as excited for me to have a car I desired so much. This was my very first and only turbo car I’ve ever owned and every time the car plants my back to the seat I can help but grin from ear to ear. 

I kept the car stock for a year on the dot before I started modifying it, if you’re keeping track it’s now April 2018. I purchased all the necessary supporting mods to keep it from going ZZB. I bought an Access port, HPFP Internals, intake, and pro tune and man did that little K04 come alive, a few other supporting mods like exhaust and rear sway bar brought the Mazdaspeed to a different level. 

Shop all 2010-2013 Mazdaspeed 3 Categories

The Speed had no changes for another year or less (early spring 2019), finally, it was time for power mods, big turbo, big FMIC, lots of little bits like injector seals, short shifter, motor mounts, and getting a tune from Purple Drank. The car became a monster, smiles turned to white knuckles gripping the wheel from torque steer, turbo noises for days, and a singing bypass valve that subtly lets you know it’s there on any occasion. 

That kept me satisfied for another year till now, this plan is to do both manifolds, cams, and EWG. *Hurray for race car noises*. The transformation of my Speed over the last 3 years has been a rewarding experience, providing me with knowledge and experience and confidence to be able to tackle any problems or situations previously I would have avoided or paid an overpriced shop to fix.

This is the best part of the community I joined when I bought my speed, all the experiences and knowledge that has been shared with me have been nothing short of amazing and I’m truly grateful for the speed community. My wife and I don’t take a lot of vacations, but the two events that come up in the year that you can’t miss are Mazda events. 

Shop Gen 1 and Gen 2 Mazdaspeed 3

I didn’t know that I could miss Idaho as much as I would when I have to leave Papa Keith’s Mazda Takeover event in Boise after a 4-day party. The big bear puts on an amazing event yearly and when it wraps up the withdrawals of it kick in. Those pains are subsided though just two months later when we all get to catch up for CorkSport’s Dyno Day’s! The event that the CorkSport crew puts together is a blast, its high tempo 2-day event that brings our Mazda community together in the Pacific Northwest, I have seen people from British Columbia to Utah come all the way to Vancouver, WA for this event. 

These two trips are something that flows into my DNA and I can’t imagine my life without experiencing them or the people I’ve met along the way. My wife and I look forward to these weekends as I’m sure anyone who has gone to them at least once will, we love spending time with our extended Mazda family and I wouldn’t change it for the world. 

In closing, to say that a car would change my life would be an understatement, but it did and I wouldn’t want it any other way, so if you see the Red Baron Speed of Newberg out and about, come up and say hi and chat for a minute. I hope to see you all at future events, keep hitting that Boost, and stay safe. See you all on the road.

  • Symon

Zach’s Road to CorkSport

The Journey to CorkSport

Ever wonder what it was like to win the lottery. You ever let your mind wander and think what it would be like to actually “Live the dream.” I know I have, well, until I joined CorkSport! My name is Zach Sprague, and I wanted to share with you my experience of joining, what I believe to be, the best well known and respected company in the Mazda Community. Let’s take a look at my journey.

I’ve always been into cars and have had a pretty big obsession with FWD Hatchbacks. My passion for this platform started back in 2014. I sold cars for Toyota in Southwest Washington for about four years. During my tenure, I drove some pretty amazing vehicles, one of them being a 2013 VRM MS3 Tech pack. I knew what a Mazdaspeed was, a Turbo FWD Hatchback, and at that time that was more than enough to pique my interest in the platform. It was temporarily sitting on my lot, and I had to drive it back down to Portland to our sister store.

Before jumping into the seat, I didn’t know any horsepower or torque figures. I didn’t know what kind of emotion it was going to spark when I drove it. I had NO idea that it would become the screen saver on my computer. I slid in and pushed the button. (You know those Cold Starts) This car’s exhaust made my heart drop and gave me goosebumps. I honestly felt like an 8-year-old on Christmas Morning. 

Once on the ramp, I slowly shift into third at about three and a half grand on the tach and just sent it. Torque steer was prevalent as I was gently pushed back into my seat. I slammed 4th, and I hear this intoxicating PSSHHHHHH. I was done, I was hooked, addicted and didn’t know what to do with myself. I was so intrigued I stopped at every rest stop on the way down so that I could feel this car accelerate back onto the freeway. <insert uncontrolled giggling here>.

Flash forward a couple of years, and a guy I worked with, now one of my best friends, went out and bought a VRM Speed6. Everything on that car from top to bottom was stock down to the wheels. I slowly watched his build progress over the year and transform into one of the most inspiring builds I have ever seen. In that time he was kind enough to let me pick his brain about these cars and what they like, what they don’t like.

In 2018 this is when things got interesting! After a few months of looking and 100 YouTube videos later, I was finally ready to pull the trigger on one of my bucket list cars. I snagged a 2013 MazdaSpeed3 in liquid Silver. I drove almost 4 hours and paid an arm and a leg for sales tax, but it was worth it.

Miles of Smiles 

I was grinning ear to ear the entire way home; 4th gear dumps on the freeway, testing the grip of the tires out at a few stoplights, full-on shenanigans. I tell you what; I made it home a lot quicker than the drive up.  

I had the car for 3 weeks before I added my first mod. I already had a vision for the car, but first things first, I had to take care of those sloppy shifts. My shifter bushings and short shift plate showed up from CorkSport. At that time I knew they made great parts and were one of the very few places that even made parts for this car. What a difference that made! It felt robust and more responsive.

The Opportunity of a Lifetime

I always joked with my friends about working for a company like CorkSport. I just thought it was this elusive dream that I’d be sitting behind a desk helping other people build their dream cars. I never thought in my life that an opportunity like this would come into fruition. 

My buddy, who helped me get into Mazdaspeeds, sent me a message on FB, letting me know that CS was hiring. I thought to myself; this is no lie. “There is no way on god’s green earth I’d ever get that lucky.” However, I applied. What’s the worst thing that could happen, right? 

CorkSport isn’t a revolving door, and the team is made up of a close-knit group of professionals that also happen to be car nuts. They carefully consider who’s going to be a good fit with their existing team and identify candidates that are going to get the right shit done well. I knew this was a different company, and their standards were high because they didn’t just accept my resume; there was a pre-test.  

A funny little story. I got a message from CorkSport saying they wanted to set up a phone interview! I couldn’t believe it! That Friday, I called to set up a meeting for Monday. This is where the humor known as my life kicked in; I BROKE MY PHONE ON SUNDAY! *RED ALERT* My dream job was calling me on Monday, and I didn’t have a phone, so I went out and bought a little prepaid flip phone. 

Although I almost missed this opportunity, it went well enough for CorkSport to schedule a second interview over Skype. I must add, this occurred over two weeks. I was losing my mind; I couldn’t believe it was happening. All my buddies knew I had the job, they knew how obsessed I am with cars, especially my speed 3. I still was in shock couldn’t believe I had my second interview.

When CorkSport called me to let me know, I had a final interview with the Company’s President, Corey – Hello nervousness, glad to see you again! I can’t put into words how excited I was; it was pure bliss and absolute disbelief. “IS THIS REALLY HAPPENING!” I screamed at the top of my lungs when I got off the phone. I showed up a half-hour early. It was cool; I got to meet someone I’ve stalked on Instagram for a while and who has been a significant influence on me since I got into the Mazda community – Brett White.

It’s so surreal when you get an interview for a job you’ve always wanted. Above all, I remember from the interview is telling Corey, “Even if I don’t get the job, knowing I made it this far and am sitting here with you having this interview is honestly a dream come true.” It’s unreal to think that one mistake, such as breaking my phone the day before my first interview, could have kept me from writing this blog for a company I’ve looked up to since I’ve been into Mazda’s.

I cannot believe I’ve been here a little over a year already! It’s a fun environment where everyone is looking out for one another. I’ve been able to FLY in the fastest thing I’ve ever been in (Barett’s monster Gen Juan), and had the chance to drive a car I’ve drooled over on social media (Brett’s Baby) for years. 

Barett’s monster Gen Juan

Looking back, it wasn’t even four days after joining the company before the guys a CS put lowering springs on my car. It took a little over a week for me to buy an AccessPort and a Dual VTA Bypass Valve, and that was just the start! You don’t want to be an employee driving a stock Speed with a CorkSport Sticker on it.

Stay tuned to see where CorkSport and I go with my car. I’ll catch you on the flipside and, thanks for reading my first blog!

Zäch Fröm CorkSport

Safely Upgrade Your Mazdaspeed Turbo

It doesn’t take long for those building power to use up the stock K04. They are prone to fail, especially when you start shoving that extra air through it. A common question is, “My Mazdaspeed is smoking, is my turbo bad?”

First things first. There is a BIG difference between replacing a bad turbo and upgrading to a more efficient one for more power. If you want to replace it, go with OEM and just plug and play, you’re good to go, wash your hands and get on with your life. This will have your car up and running pretty quickly. However, your maximum power output will be limited and you will eventually have the same problem – the KO4 will fail.

If you are saying to yourself, “It’s time to upgrade…I NEED more power in my life!” Then this blog is for you. Below, we lay out the basics needed to successfully install a CorkSport Mazdaspeed Turbo, highlighting the required supporting modifications to keep your Mazdaspeed safe. And as an added bonus, we keep our installation instructions on each of our product pages, so you can preview how easy the install will be for your experience level.

Here it is, the list is comprised of the BARE essentials to run the 18G CorkSport turbo.

HPFP INTERNALS

Giving you 50% more efficiency with your fueling system, as well as, a strong base to build power for your Mazdaspeed. The CorkSport Max Flow Fuel Pump Internals are built to directly replace your stock fuel pump internals and perform with immediate improvements.

CorkSport fuel pump vs. competitors

ACCESSPORT (or VERSATUNE if you have a CX-7)

The Cobb Accessport will give you the basis for tuning, and since this is required with the CorkSport turbo – you’ll want to make sure you have this in hand and ready for when you install your turbo.

These are the basic foundation to our Mazdaspeeds, without these two items you cannot operate your Mazda after installing an upgraded turbo.  You will need your Mazdaspeed tuned, and your tuner is going to say the same thing.

That’s it, that’s all you need to run the CorkSport Mazdaspeed turbo safely. With this proper foundation, you can put yourself in a position for efficiency, or more power.

Now the question is do you want to make it go fast and harness the power that this turbo is built for? Keep reading and we’ll provide some other awesome upgrades that are the next step once you have your turbo installed and running.  Oh, and if you are looking for a proven path to make 400WHP, check out our Chasing 400 WHP Blog here!

CorkSport Upgraded 3.5” Intake

The CorkSport turbo is rated for up to 450WHP with the right set up. Unless you are going for the MOON and shooting for over 700WHP a 3.5” intake will be more than sufficient for this turbo. Giving you some extra airflow to increase your power range, and harness what your Mazdaspeed3 is capable of. Note: Will require additional tuning!

CorkSport Mazdaspeed Downpipe

Doesn’t matter if you go with a high flow catalyst or opt-in for one without, the choice is yours. However, if you want to utilize its flow you are going to have to upgrade to a bigger diameter. Our 80mm one does really well, plus it sounds GREAT.  Note: Will require additional tuning!

The CorkSport Cat Back Exhaust System gives your new 2016 Miata the power it needs without the annoying drone.

CorkSport Cat-Back Exhaust

It’s no secret that car engines are just big air pumps, the faster you can shove air into the engine and how fast you can expel it efficiently is what it takes to make more power. No need to run the stock 63.5mm exhaust when you can run our 80mm (like to wake up the neighbors every morning, go with our non-resonated, you can’t beat the cold start)

CorkSport Top Mount Intercooler

If your power goal is 450whp or less you can get away with just upgrading your TMIC and be on your way and they look great in your engine bay.  Note: Will require additional tuning!

If you have the 2nd gen you can really utilize that hood scoop from the factory.  Not only that but you can even see a noticeable performance gain with our larger hood scoop and a TMIC set up.

When it comes to your Mazdaspeed we know you want to create safe power and harness the true potential of your ride. Be sure to build upon the proper foundation and head in the right direction for your build. Our techs are available for any questions you have and are ready to assist with planning your Mazdaspeed build path! Any questions – give us a call directly – (360)260-2675, email to sales@corksport.com or leave a comment and we’ll get back to you!

Tuning – What Are Your Options

Pretty much since I joined this platform, I’ve noticed a pattern of people asking the same questions about tuning their Mazdaspeed. There is a lot of information out there, but it’s not always consolidated or easy to find. So, in the effort to assist newcomers, this will be a write up explaining the ins and outs of tuning; when you need it, OTS vs. Pro Tunes, and how you can proceed.

*There are other options for tuning the vehicle besides the Cobb Accessport, such as Versa Tuner. But, for the ease of explanation throughout this blog, I will be referencing the AP*

What Is Tuning & Why Do You Need It?

Without getting too elaborate for this specific blog, “Tuning” is just the remapping of the tables in the ECU from OE specs to something different. It is a key aspect of your car’s engine health and the easiest way to make more HP. You can even tune a bone stock car and will typically see gains, especially when they are boosted from the factory. Bolt-on parts free up even more headroom in airflow, and when tuned accordingly you make even more power. The relationship between bolt-on parts and a tune is a beautiful thing, and hopefully, by the end of this blog, you will understand how they work together.

“So when should I get a tune?”

I’m so very glad you asked that! Well, let’s look at it like this… Mazda spent a long time getting their factory tune for the Speed 3 as good as possible. But they dialed it in around one set up, and one set up ONLY. That’s 100% OEM parts. In this form, the ECU knows what to expect, how everything should respond, and most importantly when something is wrong. It doesn’t have a mind of its own though, it only knows what it’s been told. So, if other parts in the system are replaced, and the ECU isn’t told how to react to that, things start to get a little weird.

The ECU has an ability to adjust itself within reason for variations in fuel, oxygen content, etc. But in a perfect world, it shouldn’t have to adjust itself at all. Tuning for the mods you do will not only let you have more fun, but it will get it as close to this perfect world as possible.

Minor things like an intake upgrade (Retaining stock MAF) BPV, or Catback usually won’t throw off the ECU enough to cause problems or CEL’s but it’s obviously not ideal. That being said, its best to get an Acessport or another means of tuning your Mazdaspeed prior to putting on bolt-on parts.

So here is a basic FAQ

“I want to add a turbo back exhaust, but I don’t want to get an AP and tune the car. Can I do that?”
– No, you are not able to do this for two reasons.

  • Deleting the factory cats opens a huge restriction. Without a tune, the car will risk overboosting.

  • Without fuel pump internals you also risk running lean and blowing the engine. Even if you have the internals with no tune, the drivability of the car can suffer because of how it affects the turbo.

“Can I get an intake with no tune?”

  • If its factory size, then you can usually get away with it. The turbo isn’t trying to make more boost, and the MAF housing should be accurate to the OE. If it’s a larger one like our 3” or 3.5” then no, you cannot.
    However, I always recommend tuning the car.

“Can I get a catback with no tune?”

  • Yes, you will be OK, the catback is not monitored by any sensors, and you’re not deleting any cats.

“Can I change my intercooler without a tune or fuel pump internals”

  • You should not. Just like the cats on the downpipe, the factory intercooler is a restriction. The ECU currently is tuned to fight this restriction to make a specific boost level at a specific RPM. If you remove this restriction, and you don’t tell the ECU, you risk over boosting. Over boosting mixed with no fuel pump internals can be a risky combo for running lean as well.  

“Can I upgrade my turbo without tuning the car?”

  • Definitely not, any turbo that moves more air than the factory one automatically needs a tune. The ECU is tuned to coincide with the factory compressor map. If you don’t want to tune for a turbo, make sure you get a factory replacement. These are just some of the common questions we get, but if you have more specific scenarios you can always email or call us! On to the next section.

OTS maps vs a Pro-Tune

I remember when I first got my hands on an Accessport. Trying to make sure I selected the right map and learning how to read all the parameters. I know a lot of newbies that are just getting an AP probably are asking themselves which OTS tune is the right one to use, and when should they get a Pro-Tune and how.

It’s no news to anyone that’s been in the community for a minute that the Cobb OTS maps are not the best Long-Term Solution. The reason for this is because they are:

(A) Very conservative, and not letting you get the full potential you can.
(B) Meant for a large population of cars, and aren’t really dialed in. Essentially, they are just rough around the edges.

 

However, OTS maps do serve a purpose. For someone who is planning on doing their basic bolt-ons in stages over the course of a few months then it works out well. These maps can be viewed as basic stepping stones “Stage 1, Stage 1+, Stage 2, Stage 3, Etc” that allow you to put on your first bolt-ons and flash the corresponding tune. So, as you are putting on your fuel pump internals, intake, downpipe, Intercooler, you can flash those readily available maps.

 


In a nutshell, the OTS Maps work great during the transitional phase of your modding Journey. But, once you know you are done with your bolt-ons for a bit, that’s when you want a map that is 100% dialed in, and specific for YOUR car. The difference between a custom tune and the Cobb OTS maps are truly astonishing, and you’ll see once you’re there.

Something to also note….

If your K04 ‘Sploded and you are looking at a larger turbo, an OTS is no longer an option, it’s off the table. Cobb made those OTS maps solely for a factory turbo’d Mazdaspeed. If you buy a bigger turbo like ours, a Pro-Tune is needed (along with fuel pump internals)

“Don’t I have to get the car on a dyno in order to get a Pro-Tune? There’s no Mazdaspeed tuners in my city!!!!”

If you’re not one of the lucky ones that live by a Mazdaspeed tuner, then fear not. The days of having to get it on the dyno to get a tune or over. With the Accessport, Maps are sent/downloaded over email.

To Start the process, you need to:

  1. Buy the tune

  2. Give them your full engine Mod List

  3. The tuner will instruct you on taking your Data Logs

  4. Over the course of a few weeks, you will go back and forth with new tune revisions and the car usually gets smoother and faster with each revision.

By the end of this process, you will have a dialed in tune and a smooth-running car. But, please note that if you add another part to the car or change parts. You may need to get a revision tune done to account for the new mod. Talk to your tuner about this and get their thoughts.

Recap

I hope that this helped some of you to better understand the processes you should take, and to wrap it up we will hit some of my main points.

 

  1. The first mods you should get for your Mazdaspeed if you plan to mod it is the upgraded fuel pump internals and an Accessport

  2. If you just want to run an SRI and a catback, you can get away with it, but a tune is Recommended.

  3. You should NOT run a downpipe without fuel pump internals or a tune.

  4. OTS maps are great during a transitional time with your car while bolting on parts. After this, you should get a Pro-Tune

  5. You shouldn’t run a larger turbo on the stock map or on an OTS map. Communicate with a tuner before the install and have a new base map ready.

  6. Pro-Tuners are able to tune you, even when they aren’t local.

 

To conclude this blog, it’s important to know how critical the proper tune on the car can be. It can make or break the engine, literally.

If any of you still have questions, you can always give us a call, and remember to have fun as you begin your journey down the path to making power, and giving WRX’s the L.


Happy Boosting,
Brett@CS

 

Brett’s Build Part 4

“Hey Bro, what flares are those?” A common question asked, not that I blame anyone for their curiosity.

This is a very niche platform in the grand scheme of things. So we don’t really get lots of options when it comes to widebodies or flares etc. Those of us who have been crazy enough to chop into our ¼ panels had to trust what we think will look good, cross our fingers, and just send it. Some of us get lucky, some of us don’t. I wasn’t in it alone though, I had help from a few friends, and some inspiration. So, here’s the story on how I flared my Mazdaspeed 3.

My good friend Brian over at BMSPEC has a well-known Mazda 3, named “Circuit Heart” Which just recently has gone into retirement. He was one of the first to ever put flares on the Gen 2 Mazda 3 body, and for years I said I wanted that look. When He decided to let go of his old Volks, I had the opportunity to take possession. With his direction, I ordered fair lady Z flares from that were originally meant for a 240Z.  

I asked my local Nator Buddy Aaron Maves if he was down to help me chop up my Mazda and lend me a spot in his garage. Ironically enough, he was a stoked to be a part of the project, probably more than me. Once my flares came in, I got them dropped off at the body shop to be paint matched and started hashing out a plan. Since I work all day long, and flares are a rather tedious process this was going to be a strictly after work job and it ended up taking quite some time to get done. But the wait, blood, sweat, and tears were worth it.

Here is a little step by step process we took to get it done. If you are looking to ever do this to your Mazda, it may either motivate you or deter you away.


Step 1. – Test Fitting

This part is very critical, and one of the most difficult. You have to Mock up the flare to be as perfect as possible. Usually, since the flares we try to use on our Mazda’s, they don’t exactly want to line up where we want, and we need to motivate them a bit to do so.  Painters’ tape by itself will not be enough to hold it where you need. The way I got around this is by using 3M Double Sided VHB tape on the back of where the bolts will go, paired with the painter’s tape. Since these flares weren’t made for this Mazdaspeed3,  I started out on my front driver side fender.  Once I got it where I knew I wanted it, I opened up pandora’s box. I drilled my pilot holes into the fender, no going back now. That’s not even the worst part, because now I had to make all 4 corners symmetrical (No pressure or anything).

Matching every corner is not an easy task, and also something that is often messed up. All I can say is triple check everything, and then do it again. We had to find reference points on the Speed3 itself to measure from. The ground below could be slightly inconsistent. Not only because the floor may not be perfectly level, but because the floor jacks may be slightly different as well. Choose about 4 points to measure from so you can get an accurate X/Y axis measurement to link to the other side. You’ll want the fronts to be identical, and the rears to be identical.

 

Step 2 – Rivnuts

 

Now that we have drilled pilot holes in all 4 corners. We opened them up enough to accept the riv-nuts. This will be the threaded inserts that allow you to bolt the flare to the Mazda. We had to open the hole up slowly, stepping up the size of the bit each pass. Doing this prevents the thin metal from fraying and making sharp edges around the hole. You want the riv-nut to sit as flush as possible, so the flare sits close to the body.

In this particular case, I used ¼ – 20 sized bolts, so I opened op the flare with a ¼ hole and bolted the flare on for a final fitment check.

 

Step 3 – Cutting

The most intense part of the process now begins. My buddy Devin Sorter who is a fabricator/welder came through to help with this. He’s very skilled with a cut off wheel, and I knew I could trust him to make some solid cuts that are symmetrical and clean.

With the flares mounted up, we drew the line for the cuts. Remember you not only have to give yourself enough clearance for the bumps on top, but for steering in the front as well. During this process, part of the bumper clip will have to be removed as well. This isn’t a problem though since the flare itself acts as a support and keeps the bumper from sagging, even with the splitter on the front.

 

Step 4 – Sealing the rear ¼ Panels

Since the ¼ panels in the back aren’t just 1 layer like the front, when you cut into them there is now a gap between the layers that are left open. Even though my Mazdaspeed isn’t driven in the rain, it still leaves the car open and vulnerable to getting moisture in there and eventually causing corrosion. To prevent this, you need to stitch weld the panels together and then reseal it. Once the welding was complete, we used silicone to seal it all in and protect it from the elements. We also put some weather stripping on after the fact to prevent any harsh rubbing on the wheel in case the Mazda bottomed out or the tire somehow traveled up high enough.

At this point, the Mazdaspeed3 was done, and I bolted on the flares. The gasket you use between the flare and the body is up to you, there are lots of options out there.


Thanks for checking this out and stay tuned for part 5!


Cheers,
Brett@CS