Tag: hfpf

Posted on

Brett’s Mazdaspeed 3 Build: Part 1, The Basic Beginnings

It all started in Phoenix AZ, back in 2014 when I was graduating tech school. I was finally working enough to buy a Mazdaspeed that I had wanted for a while. At this time, it probably would have been smart for me to just start saving, instead of taking on a hefty car payment. But, as a car enthusiast, I’m sure you understand the temptations we often face, and I went for it. Since then, I’ve never looked back.

Red 2013 Mazdaspeed 3

 

I found my 2013 Mazdaspeed3 in the fall. Completely spotless, 6k miles on it, and bone stock. It was truly a blank canvas. At that time I was barely making enough to own the car and pay for insurance. So, modding wasn’t an option at the time. So, as I saved and Saved, I was introduced to Nator Arizona by Thomas Graham, who later became a good friend of mine. He got me involved in the community, and on the right track for learning. From that point on, everything changed, and I loved it.

At the time, I was nothing more than a technician, fresh out of school and stuck on the lube rack for a bit. So, as you can imagine when I finally had enough to get my Accessport and Fuel Pump internals for the Mazdaspeed 3, I was STOKED. I caught the modding bug, and before I knew it, I had bigger aspirations for the car than ever thought I would have had. The next year was filled with countless Nator garage days, fun drives, Mexico pulls, and slowly adding parts when I could afford them.

By mid-2015, my time in AZ was coming to a close. At this point, I had all the basic bolt-ons offered for the Mazdaspeed 3. Rear motor mount, short ram intake, upgraded BPV,  upgraded TMIC, and turbo back exhaust. The car otherwise looked completely stock, just MUCH louder!  The icing on the cake was the pro-tune 320 WHP on Stock turbo with some e85. A couple of days later I departed AZ for my next chapter and got the MS3 on the trailer.

Towing Mazdaspeed 3

Funny looking back now, how I thought I was done with my Mazdaspeed, and that was enough power to keep me happy. Not even close! The next couple years would be the catalyst that started to shape my MS3 into what it looks like now. Stay tuned for Part 2!

Mazdaspeed 3

Connect with us

You may also like

Posted on

New Year, New Gains

As the New Year rolls around, most people are looking for a change for the better in their lives.

At CorkSport we think one of the best changes you can make is more power for your Mazdaspeed. We have all the parts you need to liven up your Mazdaspeed3 or Mazdaspeed6 in the New Year.

Safety First

One of the first things to consider when modifying your Speed is the health of its engine. Performing maintenance is very important but it only gets you so far. When adding power, one of the first modifications on your list should be the CorkSport Max Flow Fuel Pump Internals.

These pump internals allow you to maximize your stock fuel system for optimum power capabilities and safer than OE A/R ratios. This means you can add the power you want and have peace of mind that your engine will get the fuel it needs.

Put the Power Down

Like the CS fuel pump internals, the CorkSport Stage 2 RMM for Mazdaspeed 3 will not directly increase the power levels of your car; however, it helps you put all that hard-earned power down. By decreasing the amount the engine can rotate, the Rear Motor Mount allows for reduced wheel hop and torque steer while providing faster throttle response and crisper shift feel.

Even we are surprised how much this engine mount changes how a Mazdaspeed 3 feels. Don’t worry Mazdaspeed 6 guys and gals, we have an RMM for you too.

Improving Airflow

Engines in an extremely simple sense are air pumps; so the faster you can get air in and out of the system, the better. That being said, some of the simplest and easiest power gains you can get from your Mazdaspeed are from upgrading the intake and exhaust. We have seen peak gains of 25ft-lbs and 33WHP from only the CorkSport Stage 2 Intake and a CorkSport Racepipe.

Checkout the dyno sheet below.

Power and torque levels will be further increased if you install a full CorkSport Turbo Back Exhaust instead of just the race pipe section.

The catback exhaust section has proven to gain up to 14WHP while the downpipe section alone has proven to gain up to 21WHP. In the dyno graph below, the downpipe car had a CorkSport Intake installed at the same time as the downpipe (hence the 50hp gain).

If that wasn’t enough flow for you, we also offer 3” and 3.5” intakes for even more airflow into your turbo. Keep in mind though, once you get into those you will need to use a new tune to ensure your car runs optimally. But check out the extra flow you get!

Turbo Upgrade

The CorkSport Drop-In Turbo is a fantastic upgrade to the stock K04 turbo that allows your car to make more power on an equivalent boost pressure. It will work with any mods you already had on your OE Mazdaspeed turbo as the CS turbo is truly a drop in upgrade. With supplemental tuning, fueling, and supporting parts, you can push your Speed to its limits.

Stay Up-to-date with CorkSport   

The Next Level

CorkSport also manufactures parts that can take your Speed beyond the parts discussed above. A short list of the parts with the best power gains can be seen below:

  • CorkSport Intake Manifold: A higher flowing IM can support much more power than the relatively restrictive OE unit. Best when paired with a larger throttle body.

  • CorkSport Camshafts: Replacement cams with extra lift to provide increased power and torque across the entire RPM range.

  • Bigger CorkSport Turbo? Yes, there is one in development. See this blog post for details.

No matter what your goals are for this year, CorkSport is here to help you achieve them. Whether you just picked up a Mazdaspeed and are unsure where to start, or have been driving one for years and want the excitement you once had back, CorkSport has a part for you.

Daniel

CorkSport Engineer

Stay up-to-date on the latest news and product updates from CorkSport.

* indicates required