Performance Air Intake | Short Ram Intake

One of the easiest and most beneficial performance enhancements you can do for your Mazdaspeed3 ,the Short Ram Air Intake replaces your factory airbox with an open intake system allowing more air into the intake chamber. The Mazdaspeed 3 Short Ram Performance Intake includes our precision machined MAF housing made from one piece of billet aluminum with included air straightener, durable dry flow air filter, and custom reinforced silicone connector. In initial testing, the Mazdaspeed 3 Short Ram Intake netted peak gains of +12HP and +17 lb torque.

Read The BlogProduct Release! Corksport Stage One Power Series Short Ram Intake for Mazdaspeed 3

CorkSport Short Ram Intake for Mazdaspeed 3

Prevent air leaks and inaccurate readings that can cause check-engine lights: The MAF housing is precision machined from billet aluminum with included air straightener.
Durable Dry Flow Air Filter: Reusable and water resistant, this unique non-woven filter media does not require oil to filter and trap dirt and actually sheds dirt under engine vibration unlike cotton-gauze which holds contaminates until you clean the filter
Custom reinforced silicone connector constructed with multi-layer nylon braid to provide more strength and power and a smooth internal transition for less turbulence and optimal flow
Stainless steel T-bolt clamps: Comes with polished stainless and ensure an airtight seal which prevents unmetered airflow
Upgrade to a CARB legal Stage Two Mazdaspeed Intake with a Turbo Inlet Pipe For the best value on the market
Corksport Service and Support: Receive a two-year warranty, full-color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support

How To Install the Mazdaspeed 3 Short Ram Intake.

It will take you Approx. 1 hour to install.

1 hour Install Time

2/5 Difficulty

2-Year Warranty

No CEL

The power series Intake is very nice and well made from CorkSport engineers. Performance wise my car pulls a lot harder on top end and the turbo spools up a lot quicker compared to stock!!!! I love the sound!!!! Next step is down pipe once CorkSport figures out engine code, so that my Mazda dealer will work on my car under warranty. Lets get the speed 3 over 310 hp. Thanks CorkSport!

Robert B.

Robert Ball06/24/2010, 06:45 PM

← Prev

1 2 3 4 5 6 78

Next →

Write a review

Would this fit on COBB’s turbo inlet hose?

Asked by Fernando | 06/19/2023, 05:38 PM | 1 answer(s)

Hey there, does this intake come with a turbo inlet pipe to replace the stock?

Asked by Jason Vargas | 11/07/2021, 07:36 AM | 1 answer(s)

will this fit on a 07 mazda 5 ?

Asked by datmazda dude | 04/15/2021, 08:18 PM | 1 answer(s)

Were the horsepower figures arrived at with a hot engine and the hood closed? Wondering on the effects of pulling in the hot air from under the hood.

Asked by Keith | 07/12/2019, 06:23 AM | 1 answer(s)

If I already have a Corksport Turbo Inlet Pipe installed, this should attach directly to that with no issues, correct? Thanks in advance for an answer

Asked by Chaz | 02/16/2019, 12:56 PM | 1 answer(s)

Hi, is this a 3” air intake or 2 1/2”

Asked by Silas Galdamez | 02/23/2018, 02:50 PM | 1 answer(s)

Looking into intakes for my '07 ms3. Is this basically plug and play? Would I be safe doing this without a tune/HPFP internals? I don't plan on any other mods just yet.

Asked by Miguel Tejada | 10/24/2018, 08:05 AM | 1 answer(s)

Can this be run on stock MS3 2010 without high pressure fuel internals?

Asked by Spin | 08/18/2018, 02:00 PM | 1 answer(s)

Will this fit the 2008 Mazda 3 S? And is the sound people report over 3k rpms different from the sound of the intake resonator delete which also comes over 3k rpms?

Asked by Cameron | 01/12/2017, 05:43 AM | 2 answer(s)