Shipping Estimator Shipping Estimator

Mazdaspeed High Pressure Fuel Pump Internals

 
Price: $349.99
Price in points:  What are Points? 350 points
Gen-6-999-10
+
Add to wish list

HPFP for Mazdaspeed

CorkSport High-Pressure Fuel Pump (HPFP) Internals for both the Mazdaspeed 3 and Mazdaspeed 6 took over 2 years of research and development to bring innovation you can count on in your Speed3 and Speed6. The CorkSport Max Flow Fuel Pump Internals have the best in market hardening surface treatments, high strength coatings, and a machined tolerance. Our Mazdaspeed HPFP Internals will give you the most performance available for your dollar. We make these fuel pumps with precision machining methods, we then treat the surface and coat it for strength, and finally machine the internals again for a perfect fit that provides your Mazdaspeed ultra-high efficiency. Real world application will allow for a greater horsepower capability, safer air/fuel ratios, and never need to worry about fuel supply in your Mazda.


CorkSport Mazdaspeed Fuel Pump Internals Advantage
Mazdaspeed3 fuel pump upgrade chart

What's In The Box:

  • Fully Machined Installation Tools Designed to help provide the most trouble free install on the market (the keeper tool even turns into a bottle opener for your keychain).
  • High Rate Spring A higher rate spring is included in our kit for increased reliability and efficiency.
  • Designed Specifically for Mazdas The ONLY pump internals on the market designed by a Mazda performance company for the Mazda MZR engine, including Mazdaspeed 3, Mazdaspeed 6 and Turbo CX7.
  • Precision tolerances and improved efficiency 50% larger than the OEM pump internals for increased fuel volume flow.
  • Required Hardware Anodized Aluminum Installation Sleeve and Retaining Hardware included.Tough Aluminum Case For storing your factory internals or anything else that is legal.
  • CorkSport Service and Support: Receive a two year limited warranty, full color installation instructions, all of the needed installation hardware and knowledgeable telephone support.


Mazdaspeed 6 fuel pump upgrade

How To Install Your Mazdaspeed MZR DISI Max Flow Fuel Pump Internals

It will take you one hour to install the CorkSport Mazdaspeed Fuel Pump Internals with our easy-to-use instructions.

2 Hour Install Time

2 Hour Install Time

Difficulty: 3/5

3/5 Difficulty

2-Year Warranty

2-Year Warranty

No CEL

No CEL

how to install Mazdaspeed 3 high pressure fuel pump internals

New features

Manufacturer:
CorkSport
One of the best purchases I've made for my Speed3. I was going to wait until I had my AP before I installed these internals, and I wish I hadn't waited. I have my AP ordered and on the way, so I installed these in preparation. I could feel the difference as soon as I started driving. The response and ability to maintain power through the entire RPM Range is 1000 times better now that I installed these. Normally I would feel a dropoff in power around 4000 RPMs, but I feel no dropoff at this point. Finally, my engine can keep up with the weight of my foot.



Corksport SRI, Racing RMM, Internals installed.. TIP, AP, Downpipe coming soon.

Thanks Corksport!!
I got my CS stage 2 SRI prior to getting the fuel pump internals and I can feel a difference after installing. Got the AP already and now time for a Downpipe! Corksport is the best in quality and shipping time!! A++
Hi CS team!



I've installed the internal, but I also have heard that I need to wait some miles to drive the Car at full throttle.



It is true? If so, how many miles do I need to wait?
Do you need the access port to tune your car after installing the hpfp internals?
Love this part! Made a big difference in my speed6
I too had my TMIC off during the installation (like Matt G.), and getting to everything was super easy. This was the installation that I worried about the most. But with CS's super instructions and the installation video, this installation was a piece of cake. I installed the CS DP during the same install, and with the 20% increase in fuel flow pressure...I am not worried about running out of fuel at WOT!
I have ordered a few parts from Corksport already for my car. When it came time to get the fuel pump internals i didnt think to go anywhere else. Came here right away. They make a great product!!!! Cant wait to get them in and get going.
Can you put this on a 2013 Mazda 3 Skyactiv? And what would happened if you do?



Check out the FAQ tab for this part for an answer.
Changing pump internals was pretty uneventful due to good documentation and kitted parts. Hardest part was getting to the pump which just requires some time and tinkering. My stock pump held up pretty well with stage 1 mods but looking forward to stage 2 mods while holding steady at 1670 psi. I've accumulated about 1K miles on the mod and it's running perfect.
This item came very well presented. Instruction for install was very thorough and installation was a piece of cake.

Only recommendation is to remove the injector fuse and run the car till it shuts down itself before install. This way you won't have any pressure built up in the high pressure line and will not get sprayed with fuel.

After installation, the difference can be noticed straight away. Much smoother run and maintains plenty of consistent pressure.

Very happy with this product! A must have for all MS3! As always, a quality product from Corksport! Thanks!
Write a review

First mod of many; can I have my local mechanic do the install?

Asked by Jarvis | 10/22/2019, 03:59 PM | 1 answer(s)

That will work for Mazda 3 2013 2.5 auto trans (non skyactiv)

Asked by Juan  | 08/31/2019, 06:49 AM | 1 answer(s)

I went to install these internals and noticed that the little O-ring that the piston passes through had degraded in my stock pump. Any ideas short of buying a new pump would be greatly appreciated?!?

Asked by Tom | 06/19/2019, 07:49 PM | 1 answer(s)

My HPFP makes a loud clicking at the lightest touch of throttle between 2000-3000rpm. I've had CS internals in the hpfp for about 4 years. I replaced the fuel relief valve and even put in new CS HPFP internals and the problem persists. Does anyone on your team know the issue I'm experiencing and how to resolve it?

Asked by Evan | 05/11/2019, 07:25 PM | 3 answer(s)

I have a 2006 Mazdaspeed 6 and there is a Service Bulletin 01-022/08 for engine too lean at idle (P2187) will the fuel pump kit fix the weak fuel pressure at low idle?

Asked by Brad | 10/07/2017, 10:38 AM | 1 answer(s)

can i run a sri and cbe with the stock tune?

Asked by Keni | 07/07/2016, 03:46 AM | 1 answer(s)

I have the stage 2 intake and rmm insert, I don't WOT, go to tracks or race, I just use my car as a dd and I just bought the intake because I read that it would help me save on my mpg. Do I really need to upgrade my HPFP? Thank you

Asked by paul | 06/29/2016, 01:18 PM | 1 answer(s)

I upgraded my pump internals with the CS high flow fuel pump internals. I'ts possible revert the pump internals to stock, with the same stock internals removed?

Asked by Alejandro | 12/16/2016, 04:13 PM | 0 answer(s)

Is this compatible with gen 2 (2009~2013) speed 3?

Asked by cheez | 08/24/2016, 05:54 AM | 1 answer(s)

How much does this effect the fuel mileage?

Asked by Jeff | 05/16/2016, 09:00 PM | 3 answer(s)

I'm assuming that with the tappet already mated to the collar there is no further seating required? This is the only step in the process that differs from the instructions.

Asked by Jeff Magill | 04/30/2016, 02:12 PM | 1 answer(s)

I'm running stage 2 intake, boost tubes, and race pipe. Would I be safe for awhile while running theses mods. Still saving for the fuel pump

Asked by Tarango | 03/27/2016, 08:03 PM | 1 answer(s)

Can I run a stage 1 map on my 2013 mazdaspeed 3? Mods: corksport sri w/TIP, corksport cbe.

Asked by Eden Cerna | 03/21/2016, 12:26 PM | 1 answer(s)

My internals came with the tappet already mated to the collar. Is any further seating needed or just slip on? Sorry if this shows up twice, I got a send error the first time.

Asked by Jeff Magill | 04/30/2016, 02:18 PM | 0 answer(s)

Can you do an ots with the stock do pipe

Asked by George | 02/25/2016, 10:36 AM | 1 answer(s)

I've been told this should be the first upgrade to my ms6 before anything, true? I already have exhaust and short ram intake.

Asked by Ryan foley | 01/26/2016, 06:35 PM | 1 answer(s)

I feel like im beating a dead horse here but do you need any specific map to run this HPFP?

Asked by Jacob Pepel | 12/30/2015, 04:46 PM | 1 answer(s)

Is there any sort of break in period needed or recommended after the installing of this pump?

Asked by ANDY | 12/04/2015, 09:28 AM | 1 answer(s)

I bought and installed the HPFP and my relief valve blew. Im buying a new relief valve and need to know what the peak pressure the pump will make so buy the correct relief valve. Thank you in advance P.S do you have any advice on the relief valve?

Asked by Andrew | 10/28/2015, 09:30 PM | 1 answer(s)

Hello, I installed the corksport internal in a brand new hitachi pump in my gti mk5 fsi engine 2008. The stock pump works perfectly fine, however with the corksport internals the car would have difficulty to start, like if the pump is not primed, and when the car does start the ecu throw the code p2293 Fuel Pressure Regulator 2 Performance code, and the car appears to be a limp mode. No boost no power. Apparently the car is experiencing fuel starvation. When I put back the stock internal in the pump, everything is normal. Any suggestion? Should I try with the stock spring?

Asked by Laurent | 10/12/2015, 10:12 AM | 1 answer(s)

At wot sometimes cuts my fuel like a fuel cut would I need internals?

Asked by zack | 10/02/2015, 06:24 AM | 1 answer(s)

Wat advantage does this have over an entire hig pressure fuel pump? Stock Speed6

Asked by Gio | 07/06/2015, 08:30 AM | 1 answer(s)

this works for mazdaspeed3 2007-13 correct?

Asked by Joe | 06/15/2015, 11:07 AM | 1 answer(s)

Would this work with a 2014 Mazda 3?

Asked by Space | 06/09/2015, 04:28 PM | 1 answer(s)

These will work on a 2010+ ms3 right?

Asked by Isaah  | 06/02/2015, 06:34 AM | 1 answer(s)

What should my fuel pressure be at wot/cruise/idle. Im running stock internals with stage 3 corksport cai and inlet pipe. Also running the cobb stage 1 91 cs cai+inlet. Running 1700 at WOT. I need to upgrade just gotta save up. Am I safe or should I down the map to safe mode?

Asked by Derrick  | 04/30/2015, 10:09 PM | 1 answer(s)

Would this also fit the fuel pump in a VW/Audi FSI engine?

Asked by Paco | 02/28/2015, 10:37 AM | 1 answer(s)

Do you need an accessport for any changes after install, or is that optional tuning.

Asked by Mike | 01/22/2015, 06:01 AM | 1 answer(s)

Does this work with 2012 Mazda 3 2.0?

Asked by Adam | 11/18/2014, 03:07 PM | 1 answer(s)

After install the internal, do I need to avoid driving full throttle?

Asked by Jae Il Hwang Park | 11/02/2014, 11:25 PM | 1 answer(s)
Mazda and Mazdaspeed performance parts financing

Looking to finance your parts purchase and want to get 6 months NO interest on any purchase over $199? Click on the image above for more details.

Fits:
2007-2009 Mazdaspeed 3
2010-2013 Mazdaspeed 3
2007-2012 Cx7 Turbo
2006-2007 Mazdaspeed 6
2007-2009 Mazda 3 MPS
2010-2013 Mazda 3 MPS
2005-2007 Mazda 6 MPS