Introducing the first Plug-N-Play 3.5 Bar MAP sensor designed for the MZR DISI. The custom injection molded body features the OEM style connection for a quick and clean installation; no adapter wiring harness needed! With a maximum accurate pressure reading to 35PSI, the CorkSport 3.5 Bar MAP Sensor will keep you covered from K04 to Big Turbo. #ZoomZoom!

Check out the installation instructions below. Share your performance review with the CorkSport community once installed!

The CorkSport Advantage

Direct OEM Fitment

Custom injection molded body features the OEM style electrical connection for a quick and clean installation with no adapter harness needed.

Laser Etched Specs

Tuning calibration is a breeze with the necessary calibration scalars laser etched directly onto the MAP sensor.

Performance

Pressure and Temperature Response Time of 2 milliseconds.

Calibration Data

Laser Etched on Sensor

Additional Features

Compatible with: MZR DISI Engines found in Mazdaspeed 3, Mazdaspeed 6, and CX-7.
Over 20psi This is a must have part to run over 20psi of boost on your Mazdaspeed.
Includes: Black phosphate flange bolt and washer.
Designed & Developed in America: CorkSport Mazda Performance is resides in Vancouver, Washington and is located in the beautiful Pacific Northwest.
CorkSport Service & Support: 2 year limited warranty, full color installation instructions, all necessary components, and knowledgeable telephone support at (360) 260-2675.

** Recalibration with COBB Tuning Accessport is required for product installation.**

Review instructions to update scalars - discuss with your tuner.
CorkSport v1 and v2 MAP Sensors have different scalars - discuss with your tuner.
If updating a CorkSport v1 MAP Sensor with a CS v2 MAP Sensor, you will need to update your scalars - please discuss with your tuner.

How To Install Your CorkSport 3.5 Bar Plug-N-Play MAP Sensor

It will take you ~30 minutes to install the CorkSport 3.5 Bar Plug-N-Play MAP Sensor with our easy-to-use instructions.

30-Min Install Time

2/5 Difficulty

2-Year Warranty

No CEL

Does what it says. :-)

*** Do yourself a favor -- COPY THE SCALARS OFF THE MAP BEFORE YOU INSTALL IT ***

Otherwise, you'll be swearing while you try and jam your phone down in there to get a picture.

Stephan Chupack08/25/2017, 02:55 PM

Write a review

Hello sir, I’m using a Mazda3 with 2.0L skyactive in Thailand.,and I am setting a turbo for my mazda3 (Td04L) with low boost (0.3 Bar) then remap.I founded that around 2-3,000 rpm there will be some reduce and raise the throttle 2-3 times but if the Rpm is above 4,000 the throttle is working good. Me and My tuner agreed that we need to try the MAP that can read more pressure, so the question is can we put this Corksport MAP 3.5 Bar in to my Mazda3 skyactive sir? Or do you have any suggestions for me sir? Thank you very much and hope to hear some suggestions from you sir.

Asked by Krit | 11/12/2021, 02:17 AM | 1 answer(s)

what is the max reliable psi a stock k04 turbo can handle?

Asked by Anthony Clark | 09/04/2018, 03:46 AM | 1 answer(s)

Hello, I have purchased this about a year ago, installed it, tuned it per your instructions, and everything worked perfectly fine for 8 months. Now I'm getting P0107 MAP sensor voltage low, and every now and then (rare occasion) I get a P0108 MAP sensor voltage high. Hard to believe that I am getting both. Do you have any recommendations?

Asked by Justin | 08/28/2016, 01:16 PM | 1 answer(s)

I plan to run in my MSP6 20psi do I need this map?

Asked by speedy64 | 06/07/2016, 04:20 PM | 1 answer(s)

Hello, could you please post VersaTuner settings for the sensor? Thanks in advance!

Asked by Adam | 03/04/2016, 10:26 AM | 1 answer(s)

Am I able to use the accessport to use it for the tune (tune recalibration needed) or do I need an actual pro tuner like freaktune or purple drank to do it

Asked by Caezar | 02/12/2016, 06:59 AM | 1 answer(s)

How would installing this gem and new map affect my current map I'm running on the vehicle now???

Asked by Eddie | 01/30/2016, 05:57 PM | 1 answer(s)

Is this supposed to raise my psi?

Asked by Caezar | 01/13/2016, 09:28 AM | 1 answer(s)

Will this replace the need to perform AP data logs and MAF adjustments after installing a Corksport SRI and TIP?

Asked by Chuck | 01/07/2016, 07:24 AM | 1 answer(s)

New post