2014-2018 Mazda 3 Rear Motor Mount, also fits 2014-2017 Mazda 6 and 2013-2016 Mazda CX-5

Driver/Vehicle connection is a key aspect for any motoring enthusiast, and CorkSport has what you need for your Mazda!

If you are tired of the numb throttle response, gear shifts, and engine braking, then the CorkSport Race Rear Motor Mount is the performance part your Mazda needs. Excessive engine movement due to the sloppy OE RMM is just waste energy that could be going to the tires as well causes a delay feedback to your driving experience. The CorkSport Race RMM drastically reduces the amount of the engine movement, drastically enhancing your driving experience. #ZoomZoom!

Fitment for:

2014-2018 Mazda3
2014-2017 Mazda6
2013-2017 Mazda CX-5

Check out the installation instructions below. Share your performance review with the CorkSport community once installed!

The CorkSport Advantage

Perfect Fitment

The CorkSport Mazda 3 Rear Motor Mount is designed to fit and install like OE. No worries or extra parts to take your Mazda to the next level.

Design Focused

The CorkSport Race RMM combines the proper materials and design to create a motor mount that provides great performance and daily driving tolerance. The billet aluminum body is lightweight, strong, and durable with the black anodized finish.

Polyurethane Performance

Through testing and tuning, multiple durometer polyurethanes were tested to determine the optimal stiffness for performance and comfort. Durometers ranging from 60A to 90A were tested with the final result coming to 70A for the right compromise of driver feedback and daily driving comfort.

Strength In Steel

In order to properly install and torque the performance rear motor mount, precision machined black zinc coated steel sleeves are used inside the polyurethane to allow proper bolt torque to be applied.

Additional Features

Vehicle Fitment: 2014-2018 Mazda 3 and 2014-2017 Mazda 6, as well as 2013-2017 Mazda CX5
Designed in America: Designed in Vancouver, Washington, in the Pacific Northwest.
CorkSport Service & Support: 2-year limited warranty, full-color installation instructions, all necessary components, and knowledgeable telephone support at (360) 260-2675.

Advisory

NVH: Noise, Vibration, & Harshness in the vehicle cabin will be increased with the use of the CorkSport rear motor mount due to the increased stiffness. A/C use and automatic transmission equipped vehicles may further increase the NVH.

How To Install Your CorkSport Mazda Rear Motor Mount

It will take you one hour to install the CorkSport Mazda Rear Motor Mount with our easy-to-use instructions.

1 Hour Install Time

3/5 Difficulty

2-Year Warranty

No CEL

I personally find the mount too soft for my liking, but 10/10 I would/do recommend this to everybody I know who has a Mazda!

Zach 06/19/2021, 09:44 PM

Hello!

So I purchased the Corksport on 9th Dec 2020 and got it only on 15/01/2021. (I'm in Mauritius)

I installed it today and here are my feedback :
- You will feel more vibration on startup
- Compared to other reviews, I don't feel much vibration at idle even with AC on.
- The vibration is felt between 1000 to 1500 RPM
- The Shifting experience is definitely improved!
- There's no engine lurching / jerking.
- You will enjoy the Torque better! (Immediate throttle response)
- Downshift is also a pleasure when you don't feel the engine movement in the cabin.
- Compared to the genuine mount, there's more positive feedback than bad.

Regarding the vibration, i've read that it diminishes with time. So give it time before thinking to remove it. The vibration is tolerable.

I'll give some feedback after 6 months of drive.

IceSmacker 01/15/2021, 11:14 PM

Pro: good quality materials. Smooth and better response when cruising
Cons: vibration at idle/stops/traffic light in automatic w/AC On will shake your fillings lose

Ioan Kelemen 05/27/2020, 07:37 AM

I've had this mount for a while, id like to first off praise Corksport for their customer service, i had a first-gen version of this mount that was known to slipt and sure enough, mine did. When i reached out the guys at corksport sent me a brand new mount no questions asked.

The mount does its job, I do have some vibrations but I also have a straight pipe exhaust so my resluts are skewed a bit. I'd say the throttle response is helped, it has to i was able to move my engine by hand before this mount.

You cannot go wrong with this on your motor, next up for me is the trans mount, should be here soon.

Tyler

Tyler Beard 11/18/2019, 11:04 AM

This was a very easy install, the only reason it would take almost hour is to get the plastic skidplate off and on. Shifting and throttle response is very noticeable. On the cold mornings it sounds like i have a aftermarket exhaust installed.....very pleased with the product....might have to buy the transmission mount also.

Jason Eaddy 02/27/2019, 07:03 AM

Big difference with this new mount. 2017 3 2.0 AT. Why should you get it? Because the car feels like it is always in sport mode now. Shifting is so smooth when you get it exactly right, and even down shifting feels drastically different.
Throttle response is awesome and over all feed back from the car has been improved. Vibrations holding you back? Its not that bad, but they are there. Girl friend didn't even notice the vibrations until weeks later. But if you drive just for the sake of driving the reward is definitely worth the cons. Plus they are only really there when idling with the A/C on. just kick in into neutral!lol.
"why does your car vibrate? cuz RACECAR....
good quality, great service. definitely would mod with corksport again.

Jesus Ochoa 11/10/2018, 11:02 AM

Should be one of the first things you do to your Mazda3.

This mod is easy to do, and takes nearly no time at all. The feedback you get is well worth the cost of time and money.

Clutch pedal feel is increased, throttle feels a little more snapier.

If you are worried about increased vibrations:
There is an increase. It is small. 2/10 in power
You will feel a "bump" when you turn the car on.
You will feel a slight vibration coming through the seat in lower rpms (idle-1500)
With the AC on and idling, vibration increases. 4/10 in power.

Over all the increased NVH is WELL tolerable. I adjusted quickly and barely notice it now.

This mount was installed on a 2017 s Touring, 2.5/Manual.

Justin Raymer 10/21/2018, 07:35 AM

Initial impression:
No noticeable vibrations, but instead its more of a cabin resonance like a subwoofer running a constant tone at idle
At start up you feel the "hit" of the motor starting.
Its NOT severe or gonna rattle your fillings out
I can still hear and enjoy my music at idle
Yes, it gets a touch worse with the AC on

In motion:
Wow this is great!
Once moving its JUST as smooth as stock, resonance/vibration wise, unless you're lugging the wrong gear then you feel it
Shifting up through the gears is cake, way smoother transition into the next gear no more rubber band lurch into 2nd (you can actually get some 2nd gear scratch now)
Down shifting and rev matching is so so much easier and you actually can get some engine braking now!
On my test route there is a really fun L,R,L transition section where you're on and off the gas repeatedly, this is WAY better now and you feel the improved response.

If you're really sensitive to acoustic vibrations or feel the stock car has "to much road noise" then dont do this mod.

If you're a spirited driver and want more feedback from the car, do it, love it, dont look back.

Shawn Manny 09/24/2018, 08:52 AM

Easy install in about an hour and a half total, and the results are amazing. Yes, it does add vibration (I have a 2016 automatic sGT), especially at cold startup, or when the AC kicks on at idle, but unless you spend a lot of time sitting still in traffic or at lights, you’re not going to notice. The throttle response is dramatic, and the handling under power around corners is even tighter. I have mine coupled with the CS front strut tower bar, the short ram intake and the axle-back exhaust, and well, zoom-zoom has renewed meaning. The steady, direct pull of acceleration, gear shifts, braking and downshifting, and snappy response (especially in Sport mode - yeeeha!) is worth any vibration at low idle. Definitely lets out your Mazda’s inner race machine.

Eric Riggs 02/23/2018, 12:41 PM

This was my "first priority" aftermarket purchase for my 2017 Mazda 3 Sport GT. I have had the mount installed for the last 7 months and the mount is almost broken-in.

The only time I get vibrations is when the AC is on and I'm in 1st revving at low RPM. Other than that, the mount is great! No more wheel-hop and more power getting delivered to the front wheels due to the engine not thrashing around in the engine bay.

I would recommend this rear motor mount to my fellow Mazda 3 owners.

Great work Corksport, as always!

Logan 08/24/2017, 10:33 AM

← Prev

1 2 3

Write a review

Will this fit a 2015 Mazda 3 Skyactiv 2.2D? It appears that some other OE engine mounts are usable by both. Thanks

Asked by Christian Hillier | 01/12/2024, 05:10 PM | 1 answer(s)

Will it fit on cx9 2017 turbo

Asked by Thierry | 06/30/2024, 05:39 PM | 0 answer(s)

Does this fit european 2015 1.5L mazda 3 bm?

Asked by Charles | 02/03/2022, 05:04 AM | 1 answer(s)

Morning! I've had the first gen rear motor mount installed for a few years now on my 2014 Mazda6 S and have had no issues. I noticed a while back that the product was changed, but didn't give much thought to it. However, I decided to read some of the reviews this morning and noticed one poster who mentioned that the first gen had some slipping issues. Again, I haven't noticed any problems, but was thinking about getting this new 2nd gen mount. Any pressing reasons I should do this, do you think? Is there a discount or maybe a replacement option in purchasing that I might have?

Asked by Jason L | 04/21/2021, 06:16 AM | 1 answer(s)

Will this work for a 2018 6 NA2.5L with a MT?

Asked by Jason Smith | 09/04/2020, 12:37 PM | 1 answer(s)

Will it fit on Mazda 3 BM5FS model?

Asked by QY | 12/28/2019, 02:58 AM | 1 answer(s)

Are there any plans of a motor mount for the 2018 Mazda6 Turbos?

Asked by Tim | 10/11/2019, 07:53 AM | 1 answer(s)

Will this work on an 09 CX7 2.3L turbo all wheel drive? If not do you carry one that will?

Asked by Matt | 10/07/2019, 03:03 PM | 1 answer(s)

Hello I have a 2005 Mz 3 GT 2.5 L Manuel just wondering if this product works? Thanks.

Asked by Kevin Kelly | 08/31/2017, 12:23 AM | 1 answer(s)

Will this fit an 07 UK CX7? Looks similar

Asked by gareth corbett | 09/11/2017, 08:20 AM | 2 answer(s)

Purchase is considered to install it in the MT model of MAZDA3. Let me question, please. Do a shake and an allophone increase by exchanging it? When those are unpleasant, I hesitate at purchase.

Asked by MAZDA3 in JPN | 08/26/2016, 11:38 PM | 1 answer(s)

There is a question which premised on purchase. I don't do a circular course run. Basically, are these parts produced to run the general way? Only the general way is run, so when an allophone and vibration occur, I'm in trouble about installing a motor mount. When starting an engine, does vibration occur? I'm waiting for an answer. Thank you.

Asked by JPN_MZD | 08/29/2016, 10:43 PM | 1 answer(s)

How bad are the extra vibrations in a manual? Very noticeable?

Asked by Andrew Royappa | 02/27/2016, 03:19 PM | 1 answer(s)

What is the expected break-in period?

Asked by Dhiman Sengupta | 07/02/2015, 03:37 PM | 2 answer(s)

I have a 2014 2.5L automatic and was just wondering three things, firstly, will installing this have any negative sideaffects to other parts of the car? Secondly, does it come in any colors other than blue? Thirdly, since I do have an automatic is this an upgrade I should consider passing up?

Asked by Coulter McGraw | 09/15/2015, 02:45 AM | 1 answer(s)

Hi, so I a mazda3 2.0 L automatic, It's already fun to drive but I figure I ordered the cold air and exhaust already. If I'm just trying to make my car faster and a little more fun to drive would it be worth buying this part you think?

Asked by mcsluethburger | 08/19/2015, 09:00 PM | 1 answer(s)