Mazdaspeed 6 Rear Motor Mount by CorkSport

Get improved handling and shifting while maintaining a comfortable ride with the CorkSport Rear Motor Mount for Mazdaspeed 6. Designed as solid single piece, the CorkSport Mazdaspeed 6 Rear Motor Mount maintains OEM fitment while adding a large urethane thrust surface for added stiffness and improved driver responsiveness.

Read The BlogDouble Product Release! CorkSport Mazdaspeed 3/Mazda 3 and Mazdaspeed 6 Rear Motor Mount

The CorkSport Advantage:

Large Thrust Surface for reduced vibration versus other aftermarket motor mounts.
Black Anodized with Zinc Coated Sleeves for a durable, lasting finish and long life.
70 Durometer Urethane Get a stiffer ride without all the NVH (noise, vibration and harshness) associated with stiffer grade urethane.
OEM Fitment Designed as a direct OEM replacement for a worry free install
CorkSport Service and Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware and knowledgeable telephone support

mazdaspeed 6 engine mount installation instructions

Fairly easy install and so far It feels stronger under hard luanches and shifts. Hopefully it lasts the test of time but compared to factory it looks solid and a much better design.

Josh Majo11/05/2013, 09:19 PM

Great piece, no more shift thump but also no increase in vibrations like other pieces. Plus great customer service from Derrick@Corksport. Was immediately informed they were waiting on urethane to make my piece and was even refunded until I received the mount. (Which ended up only being 2 days longer than expected) Definately satisfied and excited their diff mount is now out.

Taylor Flippo08/19/2013, 09:15 AM

Good product, good results.

If it have good aging will be the best option/money

Alexander Sánchez Mendoza05/05/2013, 04:17 AM

petite vibration mais très confortable! Facile a installer! A++++++

Etienne Gendron04/05/2013, 10:44 AM

A nice piece. Very easy to install. Really helped the 1st to 2nd gear transition. No more "rubber band" feeling in the drive train as you accelerate, it all goes to the tires now. I vote best first mod to any MS6 owner.

D Lewis02/26/2013, 09:18 AM

Tried StreetUnit Billet, then Cp-e. This is way less NVH without any increase in driveline lash. Definitely the winner among this group--the others are way too noisy for daily driver.

Crosbie Watler02/25/2013, 09:36 PM

← Prev

12

Next →

Write a review

Can I safely replace the original mount with this one without needing a crane for my engine? I wont fall down? I'm just really careful. Thank you

Asked by Stijn | 12/15/2022, 12:25 PM | 1 answer(s)

This looks an awful lot like it would a 2007-9 cx7 2.3T with the 6speed AT, is there any way to test this?

Asked by John | 05/09/2021, 11:24 AM | 1 answer(s)

Will this fit a 2005 Mazda6 V6 with a 6 speed A/T? This is the OEM mount https://www.onlinemazdaparts.com/p/Mazda_2005_6-S-Sedan-30L-Duratec-V6-AT/Engine-Support-Rod-Rear/48695328/GK2C39040C.html

Asked by Emily | 01/18/2020, 07:21 AM | 1 answer(s)

Will this fit a 2007 mazda 6 Mps? Not sure if mazdaspeed 6 and mps are the same.

Asked by Henke | 11/23/2018, 12:23 AM | 1 answer(s)

Will this fit a 2008 Mazda 6i 2.3 l with automatic transmission?

Asked by Allan D Butler | 11/01/2018, 07:08 AM | 1 answer(s)

Could this be used as a replacement part for the GH OEM mount - GS1G-39-040A ?

Asked by Lucas | 01/02/2018, 06:25 PM | 1 answer(s)

Could this be used as a replacement part for the GH OEM mount - GS1G-39-040A ?

Asked by Lucas Farr | 01/02/2018, 06:26 PM | 1 answer(s)

Is this a replace part for OEM GJ6A-39-040?

Asked by Rafael | 10/21/2016, 10:57 AM | 1 answer(s)

Would this rmm be sufficient to handle a BT build being that it's only 70 duro? I really like the one I had for my speed3 but I'm not sure about this being enough for my speed6....

Asked by Casey Eberhard | 06/02/2015, 09:08 AM | 0 answer(s)

New post