Eliminate binding and remove the preload on your sway bar with the CorkSport Mazda 3 and Mazdaspeed 3 Adjustable Front End Links. Made to fit OEM and aftermarket sway bars, the CorkSport End Links have +/-6mm of adjustability, use a 5/8" hex stock that will reduce end link fatigue, and have sealed end M10x1.5 ball joints for low friction and added durability.
The CorkSport Advantage:
Sealed ball joint design: Offers low friction and is shielded for added durability and longevity
Can be used with an OEM or aftermarket sway bar*
Made from 5/8" hex stock 2011 T-3 Anodized Aluminum: For a long lasting finish and durability
No Permanent Modification: Does not require enlarging the shock mounting flange holes
Adjustable: +/- 6mm in adjustable length compared to stock to easily tune the sway bar as part of the suspension system.
CorkSport Service and Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support
* The end links have been tested and confirmed for fitment with the CorkSport and OEM sway bar. They are likely to fit most aftermarket sway bars, however CorkSport cannot guarantee fitment with a sway bar if the end link holes are not within a reasonable approximation of the OEM end link holes.
Sold as Pair
Install time 2/5 Difficulty 2 year warranty No CEL
I have the same "clunk" sounds coming underneath the car when its is cold and hit bumps (after a while they stop). it must be my 5 year OEM endlinks. will these endlinks stop that "clunk" noise?
Dimitris01/13/2014, 04:42 AM
I recently replaced my OEM's with the MOOG ones, but because of the zerk fittings, they rub when i turn full lock to full lock. These wont cause any rubbing issues will they?
CorkSport Reply:There should be no rubbing issues with the end links.
Zach11/21/2013, 04:29 AM
I could get the factory end links to deflect a little bit with my hands. These are MUCH more rigid, and made turn-in a bit more crisp.
Todd08/10/2013, 06:51 AM
are the corksport endlink bolts/studs 3/8"? +/-
CorkSport Reply:They are M10
Stephen Fancy07/30/2013, 06:06 PM
Will these work with cobb front anti swaybar? cobb's bar has 3/8" holes approx
CorkSport Reply:We have not fitted them here with the COBB swaybar.
Stephen07/29/2013, 10:41 PM
will this resolve the issue of the front end clunk? i have a 2007 mazdaspeed 3. Thanks Corksport !
Mikevelasco01/14/2013, 06:18 PM
Does this eliminate that thump, clunk, pop kind of sound? or do i need the front sway bars?
Mike01/05/2013, 09:52 AM
Do these fit both Gen 1 and 2 Speed 3s?
CorkSport Reply >>> Yes they fit both Generations.
Bryce12/09/2012, 05:57 PM
CORKSPORT Mazda 3/Mazdaspeed 3 Front Adjustable Swaybar End Links
Does this part comes with all the parts need to instulled it on my 2012 mazda speed 3? I need to know this before ordering it? >>>CorkSport Reply Yes the end links are complete, you just remove the originals and bolt these in.
Any reason you guys haven't also started offering the rear end links?
Asked by Christopher Hyndman | 06/26/2015, 08:08 AM | 1 answer(s)
The angle needed to operate along with the different rear swaybars on the market make the range of motion needed very large. To get a part to market for a decent price and meet the criteria is something we were not able to meet.