2007-2013 Mazdaspeed 3/6 Aluminum Oil Catch Can

Enhance the reliability of your engine and improve performance and fuel economy with the CorkSport Oil Catch Can. By adding an oil catch can, you will increase the longevity of your engine by helping keep unclean crankcase vapors and oil out of the engines intake. Made of billet aluminum for strength, the CorkSport Oil Catch Can includes everything you need for a complete install. Don’t let your Mazda get contaminated by sediment, crankcase vapors, or unclean oil. With the CorkSport Oil Catch Can you will remove unwanted debris that would normally contaminate the intake tract. This allows for cleaner air entering the engine, lower detonation rates and increases longevity.

The CorkSport Advantage:

Fitment:2007-2013 Mazdaspeed 3, Mazdaspeed 6, CX-7.
Superior Construction: Made from high grade billet machined aluminum for strength and low weight.
Unique Cyclonic Design: Uses vacuum force to separate the oil and contaminants from the air and includes an internal disk to prevent backflow.
Easy to Check: Twist the dipstick to check how full it is.
Complete Mounting Kit: Catch can comes complete with a black powder coated steel mounting bracket and 11 ft. of reinforced silicone hose for multiple mounting locations.*
Drain Valve Kit: Emptying the can is as simple as a flick of the wrist.
CorkSport Service and Support: Receive a two year limited warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone support.

This kit includes instructions and supplies for fitment to a Mazdaspeed 3, all other applications may require additional materials or custom modifications.
If you have the Cold Air Intake, you will need to find an alternate installation location for the catch can.
Installation note: If you live in an area which gets below zero you need to empty the catch can before the temperatures drop to maintain the functionality.
Replacing the OEM PCV system with an aftermarket Oil Catch Can System may allow smells of gasoline and oil to ventilate into the engine bay and thus the cabin depending on HVAC settings; this is normal of an Oil Catch Can System especially during idling situations and after shutting off the engine. If excessive smell is noticed, inspect hose connections and drain the catch can.
Recommended to inspect & verify the PCV is working correctly when installing the OCC Kit. Replace if needed.

How To Install the CorkSport Mazdaspeed Oil Catch Can

It will take you Approx. 2 hour to install.

2 hour Install Time

2/5 Difficulty

2-Year Warranty

No CEL

Will This Work With 09 MSP3?

CorkSport Reply: If it is a MPS3 then yes it will work.

Ronny Sanchez09/23/2013, 07:16 PM

What is the purpose of an oil catch can?

CorkSport Reply:Check out our blog https://www.corksport.com/blog/keep-your-engine-running-cleaner-and-better-with-the-corksport-aluminum-oil-catch-can-and-drain-valve-kit/ and https://www.corksport.com/blog/the-inner-workings-of-the-corksport-oil-catch-can/

Bill09/22/2013, 01:27 PM

Very solid looking piece. Kit had everything needed and install was straightforward on my 2013 Speed3. The only issue is that PCV hose is a straight nightmare to get off and getting the new hose on is also no picnic. Not a fault of the kit, just were Mazda put the thing (had to reach). Once that is done, the rest of the install is super simple.

Scott09/14/2013, 06:45 PM

have you guys found any locations that would work for 2010 speed3 other than the one you recommend? i have your CAI and don't want stuff to disappear due to inadequate mounting

James Mueller09/01/2013, 02:04 PM

Just got my OCC in the mail today. It is so beautiful. It's almost art! I will be installing it over the holiday weekend. Can't wait.

David Mackey08/29/2013, 05:48 PM

Will this fit a 2013 mazda3 skyactive 2.0?

CorkSport Reply: This will work on many vehicles, however, installation may be easier or more difficult on other models. The SkyActiv in particular is a very difficult installation due to the location of the PCV and many times requires removal of the entire intake manifold.

Tyler08/29/2013, 12:57 PM

← Prev

1 23

Write a review

Hello, is this oil catch tank is suitable for diesel engines - e.g. Mazda 6 CD 143 p.s. with DPF? Please send the answer to my e-mail. Thanks! BR Orlin Necov

Asked by Orlin Necov | 10/17/2014, 07:16 AM | 1 answer(s)

Do these oil catch cans make your car smoke at idle? Because ever since I installed the corksport OCC it's been smoking at idle

Asked by Randy Lopez | 06/26/2022, 11:24 AM | 1 answer(s)

Do I need to clean out the filters in this Catch Can or will draining the oil out when needed simply be enough?

Asked by Paulo Mello | 03/17/2022, 12:53 PM | 1 answer(s)

Is there a recommended oil and weight? Would that change when running the catch can? For a 2011 MS3. Thank you.

Asked by Mike | 06/06/2021, 05:18 PM | 1 answer(s)

Would you do everything the same from routing and placement of the catch can for a 09 mazda cx7. I was a bit confused on how it was routed but I think I understand it from the previous questions that were answered.

Asked by Taylor | 05/04/2021, 03:05 PM | 1 answer(s)

Will the standard location work with a SRI?

Asked by Austin A | 04/23/2021, 09:40 AM | 1 answer(s)

Why is this routing chosen for the OCC as opposed to a more simpler one such as the damond ms unit. Seems like itwill more pressure on the crankcase doing it the CS way. Please explain the benefits and the cons.

Asked by Alex | 04/28/2020, 06:42 PM | 1 answer(s)

What size is the ID of the vent hose? I am interested in using this in a non-Mazda application. I had one on my MS6 but sold it with the car!

Asked by Adam | 11/30/2019, 05:02 PM | 1 answer(s)

If installed with the CorkSport Aluminum Skid Plate will the skid plate need to be removed in order to drain the catch can? Are there any tips/tricks for avoiding removal of the skid try in order to drain?

Asked by Nick | 04/13/2019, 08:09 PM | 1 answer(s)

Is this OCC kit include a check valve?

Asked by Adrian | 12/17/2016, 05:45 AM | 1 answer(s)

Hi, What would it be the Placement of hose after having intalled the Mazda venting kit for smoking at Idle TBS? Thanks

Asked by Robin | 02/07/2016, 07:51 PM | 1 answer(s)

Are there concerns of aluminum can causing the hot engine air to condense in the winter and then freeze? I've hear of this in many applications during the winter, but don't like the idea of uninstalling for winter since it's such a pain to work with the pcv valve on my speed 3. Would an insulated jacket with a coolant line spiraling around the can help with any condensation and freezing?

Asked by Eric Burbank | 09/15/2015, 10:10 AM | 1 answer(s)