MAZDASPEED 3 / MAZDASPEED 6 COBB AccessPort

What's minimum requirements to run stage 1 and also stage 2?

Does it works for a Mazdaspeed3 2010 Mexico version???

Would these be able to go on a 2018 Mazda CX-5?

I made my own intake piping with a cone filter and using the stock mass air flow sensor. I just bought the high flow fuel pump internals and I will be buying the accessport tomorrow. So with those mods on my 06 MS6 will that accessport have a tune to get more hp out of my Speed6?

What is the difference between the COBB tuner and the versatuner? Can you get one or the other or does the COBB do more?

I keep seeing that Corksport has stage 2 tunes for their parts. However, I can't seem to find them anywhere on your page. When I click the link in the AP section, it takes me to Cobbs maps.

I have a Mazda speed 3 2011 I was wondering if there's any Maps I can use for corksport parts i have a, turboback exhaust and SRI with TIP, upgraded top mount intercooler, AP, and upgraded high pressure fuel pump internals

Can you turn off the seatbelt light with this? Can you turn off the check engine light if remove the catalytic converter ?

If i install the Accessport V3 in my Mazdaspeed3 2009, What is the increase number of horse power i can get ?

I have a 2010 ms3 cs catback, cs catted dp, cs hpfp, cs intake with tip, cs tmic and a Cobb ap v2. What map should I be running?

Can i use this in my 08 mazda 3 2.0

Are there any disadvantages of using your parts with Cobb's maps?

If I have the CS SRI and TIP for the Gen 1 speed, should I be running the Stage 1 or 1+ map?

I have the K&N Typhoon CAI since the last owner put it on. Is there a tune that I would be able to use with that intake?

Just got the AP, but what map will i need for CS SRI only? Custom or off the shelf map? Cobb does not want us to be running Cobb tune with CS parts. Thanks.

I have a 2008 MS3 w/ CS sri, tip, & rmm; and an obx test pipe. Which Cobb ots map would be most suitable? Please enlighten. Thanks.

Does the accessport have to be specific to the speed 6 or will the mazdaspeed 3 accessport work for the speed 6? I have the MS3 gen 1 version wondering if this would work for a mazdaspeed 6, since there is not a specific model selection.

I have the CS SRI stage II with TIP. If I get this item and set it to Cobb Stage 1, how risky is it, considering the fact that I do not have the high pressure fuel pump internals? Is it a situation of "Well, you should be ok, but that should be your next purchase," or more like "I wouldn't recommend/risk it before getting the FP upgrade?"

I have a 2013 mazdaspeed 3 with a CS Stage 1 package, CS Max Flow Fuel Pump Internals. What would be the best map for these mods and does this map come preloaded on the accessport? Would the map require any custom tuning or would i just plug and play?

Will the Cobb Tuner tell what your water temperature is. For no mazda in the last 5 years has a Water Temperature Gauge installed. Seems like a brutally insane sin to not have a water temperature gauge on a Turbocharged Mazdaspeed3. thanks

Run this whit european MS3?

Where do we get the stage 1 maps?

i just installed Acessport v3 into my mazda 3 mps 2006 , the only mod i have is the corksport stage 2 sri intake with turbo inlet pipe. how do i find the maps to tune that into the AP V3 ?

Does this monitor oil temperature? 2013 Mazdaspeed3

Is this accesspprt compatible with the 2007 Mazdaspeed3?

2010 ms3 and have a down pipe and race pipe and keep have a down stream o2 sensor slow response change sensor but happen again cause of build up would I be able to command light off for that code with access port?

I have a 2010 mazdaspeed 3 with a CorkSport Stage II Short Ram Intake, and CorkSport MZR DISI Max Flow Fuel Pump Internals what would be the best map for these mods and does this map come preloaded on the accessport? Would the map require any custom tuning or would i just plug and play?

If I have the TIP and stage 1 short ram intake can I run just a stage 1 map?

does the access port tuner come with the maps already load in it or we have to buy the maps we need after buying it?(sorry for my bad english i'm a french canadian)

Can i safely run a stage 1 tune on a stock car with absolutely no mods? Also, is the mod detectable? Say i had to take the car in for mechanical warranty repairs, if i flash back to the stock ROM, is there any way at all that the dealer would be able to tell its been flashed in the past?

Does this AP come with preloaded maps from you guys? Or would I have to go onto COBB's website and buy maps for my car?

Can this AP be used and be effective on a 2009 mazda 3 sedan with the 2.0L engine and a corksport SRI? I am looking for a tune for my car and cant find one anywhere worth getting. Thank you.

What maps would i use if I drive a 08 cx7 turbocharged? I see some say speed3 maps, but I also see that it shares the same engine as speed6

Do you guys know how to get to Cobb's map archives now? Their new website doesn't look like it supports other companies anymore

So we just use the best,matched COBB map for our Modifications?

Just got the AP and looking at the maps at the Cobb site(all the CS maps seem to be in archive). I have the stage 2 power intake set that includes the base SRI and a TIP. On the descriptions for the maps it lists TIH(turbo inlet hose) is this that same thing, or do they perform significantly different?

Does adding the CAP negate the need for a separate A/F sensor and gauge or would I still need a wideband sensor?

I currently have the Cobb AP version 2. Is there some kind of upgrade credit, like a core charge if I would purchase the V3 and send back the V2? I thought I remembered seeing this some time ago.