FREE CS Backpack!

Add $399 in Parts, Then Add Backpack!

Use Code: CSBACKPACK

360-260-2675

Vancouver, WA

HRS

M-TH 9A-11:30/12:30-5P | F-SU CLOSED

360-260-2675

Vancouver, WA

HRS

M-TH 9A-5P | F 9A-12P | SA-SU CLOSED

Home/Mazda 3 Peformance Parts/2014-2018 Mazda 3/2014-2018 Mazda 3 Power Performance Parts/2014-2018 Mazda 3 Performance Exhausts/2014-2018 Mazda 3 | 2013+ CX-5 | 2013-2017 Mazda6 Polyurethane Exhaust Hangers

Home

Shipping Estimator Shipping Estimator

Country

State/Province

Zip/postal code

Get rates

2014-2018 Mazda 3 | 2013+ CX-5 | 2013-2017 Mazda6 Polyurethane Exhaust Hangers

Price: $59.99

Price in points: What are Points?60 points

OE fitment exhaust hangers manufactured from durable polyurethane restrain unwanted exhaust movement without increasing NVH.

Set of four exhaust hangers to replace the two mid-section OE hangers and axle-back section OE hangers that are utilized with the CorkSport Performance Exhaust Systems.

OE fitment without compromise, the CorkSport exhaust hanger utilizes durable polyurethane with 75A duro hardness vs the OE 50A duro hardness.

The CorkSport exhaust hanger can be used on the downpipe, mid-pipes, and the axle-back exhaust sections.

Description
FAQ
Financing
Fitment Notes

For the driving enthusiast, high speed, canyon curves, and hard braking are all a part of the Mazda drives that we love.

This means everything on the vehicle must work harder to do the job it was designed for; sometimes those parts just are not up to the task. This results in clunking, rattles, or even a complete part failure that could have been prevented. We know you love to drive your Mazda hard so we put together a kit to keep your performance exhaust in place and in check while you fly up the mountain, slide around a cone, or hit that perfect apex. Fitment for 2014+ Mazda3, 2013-2017 Mazda6, and 2013+ CX-5. #ZoomZoom!

Check out the video below, and share your performance review with the CorkSport community once installed!

The CorkSport Advantage

Movement Control

The CorkSport exhaust hangers utilize firmer polyurethane rubber measured at 75A durometer vs the OE rubber hangers of 50-55A durometer. The stiffer polyurethane restrains the exhaust while allowing for just enough flex and movement in the system to not cause stresses which lead to cracks.

Performance Materials

Polyurethane is not your typical rubber; it’s durable, heat resistant, and will look great for years to come, outlasting the typical OE rubber hanger.

Additional Features

Made in America: Designed in Vancouver, Washington, in the Pacific Northwest.
CorkSport Service & Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support.
Fitment: The CorkSport Exhaust Hanger Kit fits the following models when using the CorkSport Performance Axle-Back and/or Cat-Back Exhaust Systems. If you are using an exhaust system that utilizes all four hangers for the axle-back section please contact CorkSport to include an additional two hangers in your kit.

2014+ Mazda 3
2013-2017 Mazda 6
2013-2016 Mazda CX-5

Fitment Note: The CorkSport Exhaust Hanger Kit fits stock or slightly larger diameter exhaust systems. Large systems aka 2.75 inches or larger will have clearance problems with the secondary O2 sensor

How To Install Your CorkSport Polyurethane Exhaust Hanger Kit

It will take you two hours to install the CorkSport Polyurethane Exhaust Hanger Kit with our easy-to-use instructions.

2 Hour Install Time

1/5 Difficulty

2-Year Warranty

No CEL

Are these included with the 80mm cat back exhaust I ordered? The fitment note gives the impression that these will not fit the 80mm (greater than 2.75”) system.

Asked by Zach McCaffree | 10/08/2025, 08:59 PM | 1 answer(s)

Will these fit the 2020+ Mazda 3 and CX-30 turbo?

Asked by Patrick | 03/10/2024, 08:19 AM | 1 answer(s)

Can be fit with mazda 3 2020+?

Asked by Nuttapon | 08/12/2024, 01:25 AM | 1 answer(s)

Will this fit the 2018 mazda6 2.5 turbo?

Asked by Alex Pepin | 01/07/2022, 06:50 PM | 1 answer(s)

I'm confused about what I need to get to accomplish my goal. I'm planning on ordering the catback exhaust for my 2014 6, and have read through the instructions. I see that 4 of these hangers are needed at the axle-back section, which seems to be what this kit is for. However, are the hangers different at the mid-pipe section, and is there a separate kit for those... or maybe a 6-piece kit?

Asked by Jason L | 04/19/2021, 07:47 AM | 1 answer(s)

how many pieces is 1 quantity? is it 4 like in the picture?

Asked by Christian Rey Burgos | 02/14/2021, 04:57 PM | 1 answer(s)

New post