2014+ Mazda 3 Polyurethane Exhaust Hangers

For the driving enthusiast, high speed, canyon curves, and hard braking are all a part of the Mazda drives that we love.

This means everything on the vehicle must work harder to do the job it was designed for; sometimes those parts just are not up to the task. This results in clunking, rattles, or even a complete part failure that could have been prevented. We know you love to drive your Mazda hard so we put together a kit to keep your performance exhaust in place and in check while you fly up the mountain, slide around a cone, or hit that perfect apex. Fitment for 2014+ Mazda3, 2013-2017 Mazda6, and 2013+ CX-5. #ZoomZoom!

Check out the video below, and share your performance review with the CorkSport community once installed!

The CorkSport Advantage

Movement Control

The CorkSport exhaust hangers utilize firmer polyurethane rubber measured at 75A durometer vs the OE rubber hangers of 50-55A durometer. The stiffer polyurethane restrains the exhaust while allowing for just enough flex and movement in the system to not cause stresses which lead to cracks.

Performance Materials

Polyurethane is not your typical rubber; it’s durable, heat resistant, and will look great for years to come, outlasting the typical OE rubber hanger.

Additional Features

Made in America: Designed in Vancouver, Washington, in the Pacific Northwest.
CorkSport Service & Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support.
Fitment: The CorkSport Exhaust Hanger Kit fits the following models when using the CorkSport Performance Axle-Back and/or Cat-Back Exhaust Systems. If you are using an exhaust system that utilizes all four hangers for the axle-back section please contact CorkSport to include an additional two hangers in your kit.

2014+ Mazda 3
2013-2017 Mazda 6
2013-2016 Mazda CX-5

Fitment Note: The CorkSport Exhaust Hanger Kit fits stock or slightly larger diameter exhaust systems. Large systems aka 2.75 inches or larger will have clearance problems with the secondary O2 sensor

How To Install Your CorkSport Polyurethane Exhaust Hanger Kit

It will take you two hours to install the CorkSport Polyurethane Exhaust Hanger Kit with our easy-to-use instructions.

2 Hour Install Time

1/5 Difficulty

2-Year Warranty

No CEL

Wanna speed up the install time of your new shiny exhaust? Great; cut those OEM junk rubber ones off and get these. It's that easy!

Dimitri Giannopoulos08/24/2023, 07:27 PM

Bought this for my 2016.5 Mazda CX-5 Touring 2wd to replace the soft squishy factory hangers. Installing the two thick ones for the CS muffler was pretty simple, the mid section was a different story. Difficult but not impossible. Probably need two more of the slim ones for the hangers hidden behind the heat shield because this set only comes in a set of four. Two thick and two slim ones, should have need 2 extra slims for the hidden ones. I’ve noticed better exhaust tone rumble because the exhaust pipes aren’t moving around as much. Not an expensive mod, gives you something to do. Remember, use plenty of lube like WD40 to get this off and put on. Screw driver may be needed also to help break it loose.

Thong Nguyen04/21/2023, 12:28 AM

These were very easy to install. A little bit of lubricant will help take the old ones off. Once installed I noticed the exhaust tone was a little better. The vibrations caused by the rear motor mount were also reduced slightly but enough to make a difference. Good product. Will definitely CorkSport again.

Jesus Ochoa12/24/2018, 06:52 AM

If you have a catback-exhaust and rear motor mount installed to your 2014+ Mazda 3, get this...As a sedan owner, I welded in longer exhaust tips to the already catback and installed the mount, but with that comes that annoying rattling sound. Installing the crankshaft pulley will help, but once you install the exhaust hangers as well, you'll be very pleased. Try driving your car very aggressively and in sport mode. You'd want to give yourself a "pat on back" for a job well done.

Eric Lapira02/11/2018, 06:40 AM

Write a review

Will these fit the 2020+ Mazda 3 and CX-30 turbo?

Asked by Patrick | 03/10/2024, 08:19 AM | 1 answer(s)

Can be fit with mazda 3 2020+?

Asked by Nuttapon | 08/12/2024, 01:25 AM | 1 answer(s)

Will this fit the 2018 mazda6 2.5 turbo?

Asked by Alex Pepin | 01/07/2022, 06:50 PM | 1 answer(s)

I'm confused about what I need to get to accomplish my goal. I'm planning on ordering the catback exhaust for my 2014 6, and have read through the instructions. I see that 4 of these hangers are needed at the axle-back section, which seems to be what this kit is for. However, are the hangers different at the mid-pipe section, and is there a separate kit for those... or maybe a 6-piece kit?

Asked by Jason L | 04/19/2021, 07:47 AM | 1 answer(s)