Mazdaspeed 3 Lowering Springs

Give your car the performance appearance and edge you have been looking for with the new & improved CorkSport Lowering Springs for 2007-2013 Mazdaspeed 3. We went back to the drawing board and revised our springs to be better than ever! With a ride height drop approximately 1.1" in the front and 1.2" in the rear, your MS3 will have quicker turning response, crisper road feel, a more aggressive appearance, and less understeer, all while maintaining OEM or better ride quality. Check out full details down below or more in depth information in our Blog with development details.

The CorkSport Advantage

Performance Driven:

The CorkSport MS3 lowering springs offer better-handling characteristics due to the decrease in ride height and increase in spring rates. Lowering your vehicle reduces the center of gravity and when combined with increased spring rates, reduces body roll on your Speed giving you the confidence to enjoy that backroad. We also increased the rear spring rates more than the fronts. This helps with comfort and reduces understeer when at the limit of traction.

Stylish Ride Height:

We went through a few different variations of springs to get the best look before settling on our final ride height drop for both GEN1 and GEN2 speeds. Compared to OEM the front gets a drop of ~1.1” while the rear gets a drop of ~1.2”. These values will vary slightly depending on the year of your speed, modifications, and what shock & strut setup you have. This is a pretty aggressive drop with springs and is just about the lowest you can go without needing a coilover setup!

Spring Rates & Testing:

The major change for the new and improved CorkSport MS3 springs is the spring rates. We tested a few different rate setups using natural frequency analysis before deciding on 3.5K front and 4.5K rear spring rates. These rates are a great balance of performance and ride quality without overpowering typical MS3 dampers, whether OEM units or aftermarket ones.

OEM Fitment:

The CorkSport Mazdaspeed3 Lowering Springs install just like OEM with no need for additional special parts. The only drawback is you have to trim your OEM bump stops to allow for correct suspension travel before the bump stops are hit. This is easily done and we have full explanations in our install instructions!

Materials & Manufacturing:

Each CorkSport Lowering Spring is made from high tensile strength spring steel for long lasting function and reliable performance. Each spring is powdercoated for a great look and corrosion resistance. The rear springs are also finished off with spring silencers to eliminate unwanted spring noise.

Additional Features

Vehicle Fitment:2007-2009 Mazdaspeed 3 and 2010-2013 Mazdaspeed 3
Designed & Developed in America: Designed in Vancouver Washington, in the Pacific Northwest.
CorkSport Service & Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support at(360) 260-2675.

While not required, we recommend replacing older dampers with new OEM dampers or aftermarket upgraded dampers.
Full range of camber adjustment may not be possible with all aftermarket camber plates.
Springs will also fit 2004-2013 Mazda 3. Ride height will be higher due to the difference in weight between Speed 3 and Mazda 3.

How To Install Mazdaspeed 3 Lowering Springs

It will take you 3 hours to install the Speed3 drop springs with our step by step instructions.

3 Hour Install Time

3/5 Difficulty

2-Year Warranty

No CEL

i was planning on installing these on oem struts and i know people say that lowering springs cause premature failure for OEM struts. Is the lowering spring designed in a way that it wont cause premature failure?

Asked by Ryan | 08/26/2023, 10:35 AM | 1 answer(s)

does these prints fit on a stock 2009 Mazda Axela

Asked by Ashton Van Engelen | 03/31/2023, 03:24 AM | 1 answer(s)

will these fit on a 2004 hatchback?

Asked by hudson schneider | 03/09/2023, 12:19 PM | 1 answer(s)

Do these spring fit on both the Mazda 3 and speed 3

Asked by Parker Ferando | 08/13/2022, 11:13 AM | 1 answer(s)

I have a 2006 mazda 3 hatch on 18” wheels with roughly the same clearance as the stock tire size. I had it rub on the fender a couple times but has since been fixed. I’m waiting to put these springs on, and was wondering if they’d be stiff enough to not rub once I put them on. I’d be fine with the camber, it’ll help with clearance, but are these stiff enough to avoid rubbing?

Asked by Samu Labrecque | 06/16/2022, 09:00 AM | 1 answer(s)