2020+ Mazda CX-30 AWD 2.5L/2.0L Cat Back Exhaust System 63.5mm
Description
Introducing the CorkSport Cat Back Exhaust for 2020+ Mazda CX-30. Add some much needed sound to the 4th GEN CX-30 and improve performance! The CS cat back exhaust replaces everything from the header back with 63.5mm fully polished, mandrel bent, stainless steel piping. It's a step up in volume and aggressiveness from the CorkSport axle back exhaust, without adding annoying drone or raspy tones.
The CorkSport Advantage
Sound Boost:
The CorkSport cat back exhaust completely replaces the OEM midpipes and restrictive OEM muffler section with 63.5mm mandrel bent pipe and pass-thru resonators. The larger pipe adds a great sound and tone for the backroads while the high-flowing resonators control drone so your car is still comfortable on the daily commute! We tested multiple resonator setups in both the axle back and midpipe sections and found that the asymmetric axle back design and large oval resonator in the midpipe results in the absolute best combination of tone, volume, and drone control for your CX30.
Horsepower Gains - Non-Turbo:
What good is sound without a little power to go with it? Installing the CorkSport Cat-Back Exhaust (with the CorkSport Short Ram Intake previously installed) netted us approximately 20wTQ and 10-18wHP. You can see significant gains from 2700rpm through the rpm range til redline at 6200rpm. Note: AWD Turbo model has not been tested.
OEM Fitment:
Each CS cat back exhaust system was designed from the ground up to fit just like your OEM exhaust system. We currently only offer midpipe setups for AWD drivetrains.
Cylinder Deactivation:
If your Mazda CX30 is equipped with cylinder deactivation don’t be worried because we have a solution for you. Utilizing a bracket made out of 304 stainless steel, you can mount your cylinder deactivation motor securely out of the way to ensure no check engine lights are set and also reduce the restriction caused by the factory internal valve.
Materials & Manufacturing:
The CorkSport CX-30 cat back exhaust is made from fully polished, mandrel bent, 304 stainless steel for a fantastic look that will stand up to the elements and keep your Mazda breathing easy. All joints use TIG welds for long-lasting strength and all hanger locations have extra bracing to ensure a secure exhaust for years to come. Lastly, each exhaust comes with all hardware and gaskets that are needed for installation to keep your installation day running smoothly!
- NVH (noise, vibration and harshness) in the cabin of your vehicle will be increased by the installation of this exhaust. We highly recommend you view the above video to hear the exhaust note inside and outside the vehicle.
- Cylinder deactivation will still function, but a more noticeable tone during cylinder deactivation will be heard with the non-use of the valve in the exhaust piping.
- Not confirmed to work with 2.0L SkyX engine. Use at your own risk.
- Exhaust will fit on vehicles equipped with the turbo engine, however, a larger CS exhaust is in development specifically for turbo models!
- Does NOT fit a CX-30 FWD Models, Designed for AWD Only.
Additional Features
- Vehicle Fitment: 2020+ Mazda CX-30 Mazda CX-30 2020-Up Mazda CX-30 2.5L Turbo and Non-Turbo AWD and 2.0L SkyG models.
- Designed & Developed in America: Designed, tested, and validated in Vancouver, Washington, in the Pacific Northwest.
- CorkSport Service & Support: Receive a 2 year warranty, full color installation instructions, all of the needed installation hardware, and knowledgeable telephone installation support at(360) 260-2675.
How To Install The 2020-up Mazda CX30 Exhaust System
It will take you 3 hours to install the Mazda CX-30 Cat Back Exhaust System with our instructions.
3 Hour Install Time
2/5 Difficulty
2-Year Warranty
No CEL
New features
- Manufacturer
- CorkSport